Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1620-83 Chassis Control System

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C1620-83 Chassis Control System

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1620 83

Chassis control system

(Chassis control system) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in chassis control module.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication line

  • Chassis control module

  • Power steering control module

FAIL-SAFE

Normal state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct adaptive Steering 3”.

Is DTC “C1620-83” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF to ON.

  2. Perform self diagnosis for "CHASSIS CONTROL".

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK CONNECTOR AND TERMINAL

  1. Ignition switch OFF.

  2. Disconnect chassis control module unit harness connector.

  3. Disconnect power steering control module harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness, connector, or terminal, securely lock the connector.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect chassis control module harness connector.

  2. Connect power steering control module harness connector.

  3. Ignition switch OFF to ON.

  4. Erase self diagnosis results for “EPS/Direct Adaptive Steering 3”.

  5. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  6. Ignition switch OFF.

  7. Get out of the Nissan Ariya vehicle and close all doors.

  8. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

  9. Ignition switch ON.

  10. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C1620–83” detected?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C1620-82 Chassis Control System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1620 82 Chassis control system (Chassis control system) Dia...
    Dtc/circuit Diagnosis. C1621-86 Bcm System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1621 86 BCM system (Body control module system) Diagnosis c...

    Other materials:

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...

    Dtc/circuit Diagnosis. C18de-82 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18DE 82 Backup power supply unit communication Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunct ...

    B24a1-16 A/c Auto Amp. Power Supply
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A1-16 A/C AUTO AMP. POWER SUPPLY (Air conditioning automatic amplifier power supply) Diagnosis condition Ignition switch ON Signal (Terminal) Accessory p ...