Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2426-11 Spindle Sensor Lh

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2426-11 Spindle Sensor Lh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2426-11

Spindle sensor LH

(Spindle sensor left hand) 		Diagnosis condition When automatic back door open/close function operate
Signal (terminal) Encoder LH signal
Threshold Automatic back door control unit cannot detect the encoder LH signal
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Spindle unit LH

  • Automatic back door control unit

  • Harness or connector (encoder LH circuit is open or shorted)

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Operate automatic back door.

  3. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK ENCODER SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “AUTO BACK DOOR”.

  3. Select “Spindle sensor LH” in “Data monitor” mode of “AUTOMATIC BACK DOOR”.

  4. Check that the function operates normally according to the following conditions.

    Monitor item Condition Status
    Spindle sensor LH Back door Open The numeral value increases
    Close The numeral value decreases

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 2.

CHECK ENCODER POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect spindle unit LH connector.

  3. Check voltage between spindle unit LH harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Spindle unit LH
    Connector Terminal
    B95 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 3.

CHECK ENCODER CIRCUIT-1

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B55 31 B95 4 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 31 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 7.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK ENCODER CIRCUIT-2

  1. Disconnect automatic back door control unit connector and spindle unit RH connector.

  2. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B55 28 B95 2 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 28 Ground No

Is the inspection result normal?

YES>>

Replace spindle unit LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2422-79 Back Door Position Abnormal
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2422-79 Back door position abnormal (Back door position abn...
    Dtc/circuit Diagnosis. B2426-12 Spindle Sensor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2426-12 Spindle sensor LH (Spindle sensor left hand) Diagno...

    Other materials:

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Power Window Main Switch Diagnosis Procedure CHECK FUSE Ignition switch OFF, and then wait for 3 minutes with driver door open. NOTE: Even after ignition switch is OFF, power is supplied to accessories for a certain amount of timer by the AUTO ACC function. When Nissan Ariya vehicl ...

    Fonctionnement du système LDW
    Témoin LDW (affiché sur l’écran d’informations du véhicule) Écran d’informations du véhicule Commandes au volant (côté gauche) Le système LDW du Nissan Rogue active la fonction d’alerte sortie de voie lorsque la vitesse du véhicule atteint environ 60 km/h (37 mi ...

    Power Distribution System. Ecu Diagnosis Information. Bcm, Ipdm E/r, Intelligent Key Unit
    Bcm, Ipdm E/r, Intelligent Key Unit List of ECU Reference ECU Reference BCM Reference Value Fail-safe DTC Inspection Priority Chart DTC Index IPDM E/R Values on the Diagnosis Tool Reference Value Fail-safe DTC Inspection Priority Chart DTC Index ...