Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B1004-11 Passenger Air Bag Module Active Vent

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B1004-11 Passenger Air Bag Module Active Vent

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B1004-11

Passenger air bag module active vent

(Passenger air bag module active vent) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuit is shorted to ground
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of passenger air bag module (active vent)

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE PASSENGER AIR BAG MODULE

  1. Replace passenger air bag module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B1004-09 Passenger Air Bag Module Active Vent
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1004-09 Passenger air bag module active vent (Passenger air...
    Dtc/circuit Diagnosis. B1004-12 Passenger Air Bag Module Active Vent
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1004-12 Passenger air bag module active vent (Passenger air...

    Other materials:

    Dtc/circuit Diagnosis. B2428-46 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-46 Automatic back door control unit (Automatic back door control unit) Diagnosis condition All times Signal (terminal) — Threshold Automatic ...

    Power Socket. Removal and Installation. Power Socket
    Power Socket Console Power Socket Removal and Installation REMOVALRemove switch panel. Refer to Removal and Installation. Press the power socket fixing pawls from the back of the switch panel to remove the power socket. : Pawl INSTALLATIONNote the following, and install in the reve ...

    Engine Stand Setting
    Setting NOTE: Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine. Ref ...