Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B0021-1b Curtain A/b Module Lh

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B0021-1b Curtain A/b Module Lh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B0021-1B

CURTAIN A/B MODULE LH

(Left Curtain Deployment Control 1) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Curtain air bag module LH signal
Threshold Curtain air bag module LH circuit resistance is above threshold
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction of harness and connector

  • Internal malfunction of curtain air bag module LH

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE CURTAIN AIR BAG MODULE LH

  1. Replace curtain air bag module LH. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B0021-1a Curtain A/b Module Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0021-1A CURTAIN A/B MODULE LH (Left Curtain Deployment Cont...
    Dtc/circuit Diagnosis. B0021-55 Curtain A/b Module Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0021-55 CURTAIN A/B MODULE LH (Left Curtain Deployment Cont...

    Other materials:

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...

    Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTCs ...