Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B0001-09 Driver Airbag Module

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B0001-09 Driver Airbag Module

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B0001-09

DRIVER AIRBAG MODULE

(Driver Frontal Stage 1 Deployment Control) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Driver air bag module signal
Threshold

Driver air bag module circuit is shorted to other

(including the spiral cable)
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE SPIRAL CABLE

  1. Replace spiral cable. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End

REPLACE DRIVER AIR BAG MODULE

  1. Replace driver air bag module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 5.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Basic Inspection. Zero Point Reset
    Description Zero point reset is an initializing procedure for occupant detection system sensor that must be performed when replacing or removing and installing passenger seat.If...
    Dtc/circuit Diagnosis. B1000-49 Air Bag Diagnosis Sensor Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1000-49 Air bag diagnosis sensor unit (Air bag diagnosis se...

    Other materials:

    P0182 Ftt Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0182 00 FTT SEN/CIRCUIT (Fuel temperature sensor ″A″ circuit low) Diagnosis condition Ignition switch ON Signal (terminal) Fuel tank temperature s ...

    With Idle Start/stop. Symptom Diagnosis. Charging System
    Charging System Symptom Table Symptom Reference Discharged 12V battery Refer to Work Flow (With EXP-800 NI or GR8-1200 NI) or Work Flow (Without EXP-800 NI or GR8-1200 NI). The charge warning lamp does not illuminate when the ignition switch is set to ON. The charge warning lamp ...

    U2252 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2252 83 CAN comm err (ADAS control unit) [CAN comm err (ADAS control unit)] Diagnosis condition Ignition switch ON Signal (terminal) CAN communication ...