Nissan Rogue manuals

Nissan Rogue Service Manual: Door switch

Nissan Rogue Service Manual / Body exterior, doors, roof & vehicle security / Power Window Control System / DTC/circuit diagnosis / Door switch

WITH INTELLIGENT KEY

WITH INTELLIGENT KEY : Component Function Check

1.CHECK FUNCTION

  1.  Select "DOOR LOCK" of "BCM" using CONSULT.
  2.  Select "DOOR SW-DR", "DOOR SW-AS", "DOOR SW-RL", "DOOR SW-RR", in "Data Monitor" mode.
  3.  Check that the function operates normally according to the following conditions.

Check function

Is the inspection result normal? YES >> Door switch is OK.

NO >> Refer to PWC-50, "WITH INTELLIGENT KEY : Diagnosis Procedure".

WITH INTELLIGENT KEY : Diagnosis Procedure

Regarding Wiring Diagram information, refer to DLK-69, "Wiring Diagram".

1.CHECK DOOR SWITCH INPUT SIGNAL

  1.  Turn ignition switch OFF.
  2.  Disconnect malfunctioning door switch connector.
  3.  Check signal between malfunctioning door switch harness connector and ground using oscilloscope.

Check door switch input signal

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK DOOR SWITCH CIRCUIT

  1.  Disconnect BCM connector.
  2.  Check continuity between door switch harness connector and BCM harness connector.

Check door switch circuit

  1. Check continuity between door switch harness connector and ground.

Check door switch circuit

Is the inspection result normal? YES >> Replace BCM. Refer to BCS-75, "Removal and Installation".

NO >> Repair or replace harness.

3.CHECK DOOR SWITCH

Refer to PWC-51, "WITH INTELLIGENT KEY : Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace malfunctioning door switch. Refer to DLK-269, "Removal and Installation".

4.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> Inspection End.

WITH INTELLIGENT KEY : Component Inspection

1.CHECK DOOR SWITCH

  1.  Turn ignition switch OFF.
  2.  Disconnect malfunctioning door switch connector.
  3.  Check continuity between door switch terminals.

Check door switch

Is the inspection result normal? YES >> Inspection End.

NO >> Replace malfunctioning door switch. Refer to DLK-269, "Removal and Installation".

WITHOUT INTELLIGENT KEY

WITHOUT INTELLIGENT KEY : Description

Detects door open/close condition.

WITHOUT INTELLIGENT KEY : Component Function Check

1.CHECK FUNCTION

  1. Select "DOOR LOCK" of BCM using CONSULT.
  2.  Select "DOOR SW-DR", "DOOR SW-AS", "DOOR SW-RL", "DOOR SW-RR", in Data Monitor mode.
  3.  Check that the function operates normally according to the following conditions

Check function

Is the inspection result normal? YES >> Door switch is OK.

NO >> Refer to DLK-319, "Diagnosis Procedure".

WITHOUT INTELLIGENT KEY : Diagnosis Procedure

Regarding Wiring Diagram information, refer to DLK-293, "Wiring Diagram".

1.CHECK DOOR SWITCH INPUT SIGNAL

  1.  Turn ignition switch OFF.
  2.  Disconnect malfunctioning door switch connector.
  3.  Check signal between malfunctioning door switch harness connector and ground using oscilloscope.

Check door switch input signal

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK DOOR SWITCH CIRCUIT

  1.  Disconnect BCM connector.
  2.  Check continuity between door switch harness connector and BCM harness connector.

Check door switch circuit

  1. Check continuity between door switch harness connector and ground.

Check door switch circuit

Is the inspection result normal? YES >> Replace BCM. Refer to BCS-135, "Removal and Installation".

NO >> Repair or replace harness.

3.CHECK DOOR SWITCH

Refer to DLK-150, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace malfunctioning door switch. Refer to DLK-385, "Removal and Installation".

4.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> Inspection End.

WITHOUT INTELLIGENT KEY : Component Inspection

1.CHECK DOOR SWITCH

  1.  Turn ignition switch OFF.
  2. Disconnect door switch connector.
  3.  Check door switch.

Check door switch

Is the inspection result normal? YES >> Inspection End.

NO >> Replace malfunctioning door switch. Refer to DLK-385, "Removal and Installation".

Power window relay
Description Power is supplied to the main power window and door lock/unlock with BCM control. Component Function Check 1. CHECK POWER WINDOW RELAY POWER SUPPLY CIRCUIT Check that an operation no ...

Symptom diagnosis
...

Other materials:

C1716, C1717, C1718, C1719 transmitter (pressure data)
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.  Activate and display TPMS sensor IDs  Display tire pressure reported by the TPMS sensor  Read TPMS DTC ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-46534) Trim Tool Set Removing trim components ...

P2122, P2123 APP sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2122 APP SEN 1/CIRC (Throttle/pedal position sensor/switch ″D″ circuit low) An excessively low voltage from the APP sensor 1 is sen ...

© 2014-2025 Copyright www.nirogue.com