Nissan Rogue (T33) 2021-Present Service Manual: Diagnostic Can Communication Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Diagnostic Can Communication Circuit

Diagnosis Procedure

CONNECTOR INSPECTION

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Data link connector

    • 8CH CAN gateway

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    • With type B meter

      8CH CAN gateway harness connector Continuity
      Connector No. Terminal No.
      M16 5 3 Existed
      4 2 Existed

    • With type A meter

      8CH CAN gateway harness connector Continuity
      Connector No. Terminal No.
      M9 41 39 Existed
      40 38 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector terminals.

  • With type B meter

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M16 5 4 Not existed

  • With type A meter

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M9 41 40 Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair or replace the root cause.

CHECK HARNESS CONTINUITY (SHORT CIRCUIT)

Check the continuity between the 8CH CAN gateway harness connector and the ground.

  • With type B meter

    8CH CAN gateway harness connector Ground Continuity
    Connector No. Terminal No.
    M16 5 Not existed
    4 Not existed

  • With type A meter

    8CH CAN gateway harness connector Ground Continuity
    Connector No. Terminal No.
    M9 41 Not existed
    40 Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check the harness and repair or replace the root cause.

CHECK 8CH CAN GATEWAY TERMINATION CIRCUIT

  1. Remove the 8CH CAN gateway.

  2. Check the resistance between the 8CH CAN gateway terminals.

    • With type B meter

      8CH CAN gateway Resistance (Ω)
      Terminal No.
      5 4 Approx. 108 – 132
      3 2 Approx. 108 – 132

    • With type A meter

      8CH CAN gateway Resistance (Ω)
      Terminal No.
      41 39 Approx. 108 – 132
      40 38 Approx. 108 – 132

Is the measurement value within the specification?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the diagnostic CAN communication circuit.

NO>>

Replace the 8CH CAN gateway.

    It Can Communication 3 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the ...
    Can Gateway. Precaution. Precautions
    Precautions PRECAUTIONS FOR SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG AND SEAT BELT PRE-TENSIONER : Precautions The Supplemental Restraint System such as “AIR BAG” and “...

    Other materials:

    Side Radar (front Right) (side Radar Front Rh)
    C1ec0-44 Control Unit DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1EC0 44 Control unit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold If side radar front RH ...

    Dtc/circuit Diagnosis. C161a-82 Abs System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161A 82 ABS system (Anti-lock braking system ) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold ...

    Dtc/circuit Diagnosis. B2ccf-04 Passenger Door Mirror Control Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2CCF-04 Passenger door mirror control module (Passenger door mirror control module) Diagnosis condition Ignition switch is ON or OFF (auto ACC status). Signal ...