Nissan Rogue (T33) 2021-Present Service Manual: C1f40-04 Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f40-04 Ecm

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F40 04

ECM

(Engine control module) 		Diagnosis condition When AEB system is ON
Signal (terminal) —
Threshold If ECM is malfunctioning
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ECM

  • ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • RAB

  • LDW

  • I-LI

  • BSW

  • I-BSI

  • RCTA

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F40-04” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the AEB system ON.

  3. Perform “All DTC Reading” with CONSULT.

  4. Check if the “C1F40-04” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F40-04” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1F40 04

ECM

(Engine control module) 		Diagnosis condition When engine is running
Signal (terminal) CAN communication signal
Threshold If ADAS control unit 2 detects an error signal that is received from ECM via CAN communication
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ECM

FAIL-SAFE

The following systems are canceled.

  • Vehicle speed & vehicle-to-vehicle control function

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • TSR

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C1F40-04” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Turn the MAIN switch of ProPILOT Assist 2.1 system ON.

  3. Perform “All DTC Reading” with CONSULT.

  4. Check if the “C1F40-04” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F40-04” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C1F40-04” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM SELF-DIAGNOSIS OF ECM

Check if any DTC is detected in “Self Diagnostic Result” of “ENGINE”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

    C1f37-55 Switch Information
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F37 55 Switch information (Switch information) Diagnosis condi...
    C1f41-84 Cvt
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F41 84 TRANSMISSION CIRCUIT...

    Other materials:

    Heated steering wheel
    Example Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light A will illuminate once the system is active. If the steering wheel surface temperature is below 86–104ºF (30–40ºC), the system will automatically heat the wheel and cycle o ...

    P0103 Maf Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0103 00 MAF SEN/CIRCUIT-B1 (Mass or volume air flow sensor "A" circuit high) Diagnosis condition Turn ignition switch ON Engine running at idle ...

    Basic Inspection. System Initialization
    Description Initialization of system should be conducted after the following conditions: Refer to Work Procedure. When the moonroof motor assembly or sunshade motor assembly is replaced. When the moonroof or sunshade does not operate normally. (Incomplete initialization conditions) Wor ...