Nissan Rogue (T33) 2021-Present Service Manual: C1215-13 Oil Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Transmission & Driveline :: Driveline / Transfer: Ty92a :: Dtc/circuit Diagnosis / C1215-13 Oil Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detecting condition
C1215-13

OIL TEMPERATURE SENSOR

(Oil temperature sensor) 		Diagnosis condition

  • Ignition switch: ON

  • Nissan Ariya Vehicle running
Signal Transfer oil temperature signal  (terminal #2)
Threshold Transfer oil temperature sensor is open.
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Malfunction of transfer oil temperature sensor

  • Transfer oil temperature sensor circuit. (Sensor circuit is open)

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Drive at 10 km/h (6 MPH) or more for approximately 5 minutes in urban areas.

  3. Stop the Nissan Ariya vehicle.

  4. Perform "Self diagnosis result" mode of “AWD/4WD”.

Is DTC “C1215-13” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TRANSFER OIL TEMPERATURE SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect transfer oil temperature sensor harness connector.

  3. Check the continuity between transfer oil temperature sensor harness connector and ground.

    Transfer oil temperature sensor — Continuity
    Connector Terminal
    F10 2 Ground Yes

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness or connector.

CHECK TRANSFER OIL TEMPERATURE SENSOR SIGNAL CIRCUIT

  1. Disconnect AWD control unit harness connector.

  2. Check the continuity between AWD control unit harness connector and transfer oil temperature sensor harness connector.

    AWD control unit Transfer oil temperature sensor Continuity
    Connector Terminal Connector Terminal
    C75 2 F10 1 Yes

  3. Check the continuity between AWD control unit harness connector and ground.

    AWD control unit — Continuity
    Connector Terminal
    C75 2 Ground No

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace damaged parts.

CHECK TRANSFER OIL TEMPERATURE SENSOR SIGNAL

  1. Connect AWD control unit harness connector.

  2. Ignition switch ON.

    CAUTION:

    Never start the engine.

  3. Check the voltage between transfer oil temperature sensor harness connector and ground.

Transfer oil temperature sensor — Voltage
Connector Terminal
F10 1 Ground 4.75 – 5.25 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the AWD control unit. Refer to Removal and Installation.

CHECK TRANSFER OIL TEMPERATURE SENSOR

Check transfer oil temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace transfer oil temperature sensor. Refer to Removal and Installation.

CHECK TERMINALS AND HARNESS CONNECTORS

  • Check AWD control unit pin terminals for damage or loose connection with harness connector.

  • Check transfer oil temperature sensor pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1215-13” is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly .

NO>>

Repair or replace damaged parts.

    C1215-12 Oil Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1215-12 OIL TEMPERATURE SENSOR (Oil temperature sensor) Diagnos...
    C1216-11 Actuator
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1216-11 MOTOR (Motor) Diagnosis condition Ignition switch: ON N...

    Other materials:

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    C106e-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106E 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...

    P02ee Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02EE 00 Cylinder 1 injector (Cylinder 1 Injector Circuit Range/Performance) Diagnosis condition Injector compensation control is operating Signal — ...