Nissan Rogue (T33) 2021-Present Service Manual: C1201-46 Awd Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Transmission & Driveline :: Driveline / Transfer: Ty92a :: Dtc/circuit Diagnosis / C1201-46 Awd Control Unit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detecting condition
C1201-46

CONTROLLER

(Controller) 		Diagnosis condition Ignition switch: ON
Signal —
Threshold Internal circuit malfunction of AWD control unit
Diagnosis delay time Within 1 second

POSSIBLE CAUSE

Internal malfunction of AWD control unit

FAIL-SAFE

Although AWD control is canceled, the vehicle can drive at 2WD condition.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always place ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Wait for 15 seconds or more.

  3. Perform "Self diagnosis result" mode of “AWD/4WD”.

Is DTC “C1201-46” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSIS

CONSULT

  1. Erase "Self diagnosis result" mode of “AWD/4WD”.

  2. Ignition switch OFF.

  3. Wait for 10 seconds or more.

  4. Ignition switch ON.

  5. Wait for 15 seconds or more.

  6. Perform "Self diagnosis result" mode of “AWD/4WD”.

Which DTC is detected?

Including other DTC>>

Other DTCs present, perform the trouble diagnosis for detected other DTC. Refer to DTC Index.

C1201-46 only>>

GO TO 2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control unit pin terminals for damage or loose connection with harness connector.

Is inspection result normal?

YES>>

After placing the ignition switch OFF, perform DTC confirmation procedure again. If DTC “C1201-46” is detected, replace actuator assembly due to the malfunction of the AWD control unit. Refer to Disassembly and Assembly.

NO>>

Repair or replace error-detected parts.

    Transfer: Ty92a. Dtc/circuit Diagnosis
    C1201-4b Awd Control Unit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1201-4B CONTROLLER (Controller) Diagnosis condition Ignition sw...

    Other materials:

    System Description. Component Parts. Interior Lamp Control System
    Interior Lamp Control System Interior Lamp Appearance and Bulb Specifications No. Item Type Wattage (W) Push-button ignition switch illumination LED — Map lamp Wedge 8 Vanity mirror lamp Wedge 5 Glove box lamp*1 — 1.4 Room lamp*2 We ...

    Mixture Ratio Self-Learning Value Clear
    Description This describes how to erase the mixture ratio self-learning value. For the actual procedure, follow the instructions in “Diagnosis Procedure”. (For details, refer to Work Procedure.) Work Procedure START With CONSULT Start engine and warm it up to normal operating tempe ...

    With Idle Start/stop. Basic Inspection
    Diagnosis and Repair Work Flow Work Flow (With EXP-800 NI or GR8-1200 NI) CHARGING SYSTEM DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NITo test the charging system, use the following special service tools: EXP-800 NI Battery and electrical diagnostic analyzer GR8-1200 NI Multitasking battery and ...