Nissan Rogue (T33) 2021-Present Service Manual: C1076-55 Not Configured

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1076-55 Not Configured

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1076 55

Not configured

(Not configured) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When configuration is not complete.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC
Configuration is not complete

  • Configuration is not complete

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Bake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch ON.

  2. Perform self-diagnosis for “ABS”.

Is DTC “C1076-55” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

PROGRAMMING OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Perform programming of ABS actuator and electric unit (control unit). Refer to Work Procedure.

CAUTION:

Do not replace the ABS actuator and electric unit (control unit) until self-diagnosis has been completed.

>>

GO TO 2.

CHECK SELF-DIAGNOSIS

CONSULT

Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1076-55” in self-diagnosis for “ABS”.

>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

    C1073-01 Vacuum Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1073 01 Vacuum sensor (Vacuum sensor) 1 Diagnosis condition...
    C1077-55 Dds Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1077 55 DDS switch (DDS switch) Diagnosis condition When ig...

    Other materials:

    U2143-57 Vcm/hpcm
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2143 57 CAN communication error (VCM/HPCM) Diagnosis condition — Signal (terminal) — Threshold MAC communication er ...

    Crevaison
    Système de contrôle de la pression des pneus (TPMS) Ce véhicule Nissan Rogue est équipé du système de contrôle de la pression des pneus (TPMS), conçu pour assister le conducteur dans la surveillance permanente de la pression des pneumatiques afin d’améliorer la sécurité, la stabilité ...

    Evtc Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the electric intake valve timing control module for damage, bend and loose connection (unit side and connector side). ...