Nissan Rogue (T33) 2021-Present Service Manual: B2730-88 Side Sensor [rl]

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / B2730-88 Side Sensor [rl]

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2730-88

SIDE SENSOR [RL]

(Side sensor [RL]) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Communication error
Diagnosis delay time 4 seconds or more

POSSIBLE CAUSE

  • Harness and connector between sonar control unit and rear sonar sensor LH side

  • Rear sonar sensor LH side

FAIL-SAFE

Stop the obstacle detection function

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check the DTC.

Is DTC “B2730–88” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK REAR SONAR SENSOR SIGNAL LH SIDE CIRCUIT (1)

  1. Turn ignition switch OFF.

  2. Disconnect sonar control unit connector and rear sonar sensor LH side connector.

  3. Turn ignition switch ON.

  4. Check voltage between sonar control unit harness connector and ground.

    Sonar control unit (-) Voltage (Approx. )
    Connector Terminal
    B49 49 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK REAR SONAR SENSOR SIGNAL LH SIDE CIRCUIT (2)

  1. Turn ignition switch OFF.

  2. Check continuity between rear sonar sensor LH side harness connector and ground.

Rear sonar sensor LH side Ground Continuity
Connector Terminal
B463 2 Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Connect sonar control unit connector and rear sonar sensor LH side connector.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B2730-88 detected again?

YES>>

Replace the rear sonar sensor LH side. Refer to Removal and Installation.

NO>>

INSPECTION END

    B2730-83 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-83 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition...
    B2730-92 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-92 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition...

    Other materials:

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    I-BSI driving situations
    Basic information Indicator on Indicator off Indicator flashing Illustration 1 — Approaching from behind Another vehicle approaching from behind Illustration 1: When another vehicle enters the monitored area from the rear in an adjacent lane, the side indicator light on the Nissan Rogue i ...

    Corrosion protection
    Most common factors contributing to vehicle corrosion Moisture-retaining dirt and debris build-up inside body cavities or seams. Paint or coating damage caused by gravel, small stones or minor collisions. Environmental factors influencing corrosion rate Moisture Sand, dirt and water accumulat ...