Nissan Rogue (T33) 2021-Present Service Manual: B2723-34 Corner Sensor [rr]
DTC Description
DTC DETECTION LOGIC
| DTC | CONSULT screen items (Trouble diagnosis content) | DTC detection condition | ||
|---|---|---|---|---|
| B2723-34 |
CORNER SENSOR [RR] (Corner sensor [RR]) |
Diagnosis condition | When ignition switch is ON | |
| Signal (terminal) | Rear sonar sensor signal RH outer | |||
| Threshold | An abnormal sensor signal is input from sonar sensor (Pulse signal high side is short) | |||
| Diagnosis delay time | 4 seconds or more | |||
POSSIBLE CAUSE
-
Harness and connector between sonar control unit and rear sonar sensor RH outer
-
Rear sonar sensor RH outer
FAIL-SAFE
Stop the obstacle detection function
CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 30 seconds.
-
Turn ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.
-
Check the DTC.
Is DTC “B2723–34” detected?
YES>>Refer to Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
Diagnosis Procedure
CHECK REAR SONAR SENSOR SIGNAL RH OUTER CIRCUIT (OPEN)
-
Turn ignition switch OFF.
-
Disconnect sonar control unit connector and rear sonar sensor RH outer connector.
-
Check continuity between sonar control unit harness connector and rear sonar sensor RH outer connector
Sonar control unit Rear sonar sensor RH outer Continuity Connector Terminal Connector Terminal B20 10 B460 2 Existed
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair the harness or connector.
CHECK REAR SONAR SENSOR RH OUTER GROUND CIRCUIT
Check continuity between sonar control unit harness connector and rear sonar sensor RH outer harness connector.
| Sonar control unit | Rear sonar sensor RH outer | Continuity | ||
|---|---|---|---|---|
| Connector | Terminal | Connector | Terminal | |
| B20 | 14 | B460 | 3 | Existed |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair the harness or connector.
CHECK REAR SONAR SENSOR SIGNAL RH OUTER
-
Connect sonar control unit connector and rear sonar sensor RH outer connector.
-
Turn ignition switch ON.
-
Check the signal between sonar control unit terminals as per the following condition.
+ − Condition Voltage Sonar control unit Connector Terminal Connector Terminal B20 10 B20 14 -
Shift position is in R position.
-
When the sensor is detecting an obstacle

-
Is the inspection result normal?
YES>>Replace the sonar control unit. Refer to Removal and Installation.
NO>>Replace the rear sonar sensor RH outer. Refer to Removal and Installation.
Other materials:
Dtc/circuit Diagnosis. B0010-11 Assist A/b Module
DTC Description
DTC DETECTION LOGIC DTC No.
CONSULT screen items
(Trouble diagnosis content) DTC Detection Condition
B0010-11
ASSIST A/B MODULE
(Passenger Frontal Stage 1 Deployment Control)
Diagnosis condition
When ignition switch is ON.
Signal (terminal)
Passenger air ba ...
Dtc/circuit Diagnosis. Horn Function
Component Function Check
CHECK FUNCTION
CONSULT
Ignition switch OFF.
Perform “Horn” in “Active test” mode of “IPDM E/R”.
Check the horn operation.
Test item Description
Horn
On
Horn
Sounds (for 20 ms.)
Is the operation normal?
YES>>
Ins ...
B2730-13 Side Sensor [rl]
DTC Description
DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2730-13
SIDE SENSOR [RL]
(Side sensor [RL])
Diagnosis condition
When ignition switch is ON
Signal (terminal)
Rear sonar sensor signal LH side
Threshold
H ...
