Nissan Rogue (T33) 2021-Present Service Manual: B24a4-11 Intake Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Manual Air Conditioning :: Dtc/circuit Diagnosis / B24a4-11 Intake Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
B24A4-11

INTAKE SENSOR

(Intake sensor) 		Diagnosis condition Ignition switch ON
Signal (Terminal) Intake sensor signal
Threshold The intake sensor recognition temperature is too high [more than 212°F (100°C)]
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Intake sensor

  • A/C amp.

  • Harness or connectors (the sensor circuit is shorted to ground)

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select "Self diagnosis result" mode of "HVAC".

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK INTAKE SENSOR SIGNAL

  1. Ignition switch ON.

  2. Check voltage between A/C amp. harness connector.

    A/C amp. Voltage
    Connector Terminal
    (+) (-)
    M54 23 26

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK INTAKE SENSOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect intake sensor connector.

  3. Ignition switch ON.

  4. Check voltage between intake sensor harness connector and ground.

    (+) (-)

    Voltage

    (Approx.)
    Intake sensor
    Connector Terminal
    M135 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 4.

CHECK INTAKE SENSOR

Check intake sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Replace intake sensor. Refer to Removal and Installation.

CHECK INTAKE SENSOR POWER SUPPLY CIRCUIT FOR SHORT

  1. Ignition switch OFF.

  2. Disconnect A/C amp. connector.

  3. Check continuity between intake sensor harness connector and ground.

    Intake sensor (—) Continuity
    Connector Terminal
    M135 1 Ground No

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

Component Inspection

CHECK INTAKE SENSOR

  1. Ignition switch OFF.

  2. Remove intake sensor. Refer to Removal and Installation.

  3. Check resistance between intake sensor terminals. Refer to applicable table for the normal value.

    Terminal Condition Resistance: kΩ
    Temperature: °C (°F)
    1 2 −20 (−4) 23.60
    −10 (14) 13.46
    0 (32) 8.00
    10 (50) 4.93
    20 (68) 3.14
    25 (77) 2.54
    30 (86) 2.06
    40 (104) 1.39

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace intake sensor. Refer to Removal and Installation.

    B24a2-55 Configuration Not Implement
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24A2-55 Configuration not implement (Configuration not impl...
    B24b4-02 A/c Control Comm
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24B4-02 A/C CONTROL COMM (Air conditioning control communic...

    Other materials:

    Repairing Procedures and Precautions
    Fundamentals of Body Repair Fundamentals of Body Repair There are many kinds of damage caused by collisions.Therefore, the appropriate repair method for the damage should be selected. This section outlines repair methods of major damage and how to use the main tools.BODY REPAIR FLOWCHART ...

    Symptom Diagnosis. Take Away Warning Does Not Operate
    Diagnosis Procedure CHECK COMBINATION METER BUZZER Check combination meter buzzer. Refer to Diagnosis Procedure (Full TFT meter) or Diagnosis Procedure (7 inch information display). Is the inspection result normal? YES>> GO TO 2. NO>> Repair or replace the malfunctioning parts. ...

    Modes de fonctionnement des essuie-glaces
    Type A (selon équipement) Type B (selon équipement) Les commandes de visibilité de votre Nissan Rogue s'activent lorsque le contact est sur "ON" : Mode AUTO / Intermittent : - Type A (Automatique) : Le Nissan Rogue ajuste seul la vitesse selon l'intensité de la pluie ...