Nissan Rogue manuals

Nissan Rogue Service Manual: B00D5 front passenger air bag off indicator

DTC Logic

DTC DETECTION LOGIC

With CONSULT

CONSULT name

DTC

DTC detecting condition

Repair order

PASSENGER AIRBAG INDICATOR CIRCUIT [FAIL] B00D5 Front passenger air bag OFF indicator is malfunctioning. Refer to SRC-91, "Diagnosis Procedure".
PASSENGER AIRBAG INDICATOR CIRCUIT [OPEN] Front passenger air bag OFF indicator circuit is open.
PASSENGER AIRBAG INDICATOR CIRCUIT [VB-SHORT] Front passenger air bag OFF indicator is shorted to a power supply circuit.
PASSENGER AIRBAG INDICATOR CIRCUIT [GND-SHORT] Front passenger air bag OFF indicator is shorted to ground.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-91, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-91, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-91, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

NOTE: All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal?

YES >> GO TO 2.

NO >> Perform one of the following repairs:

2.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.FRONT PASSENGER AIR BAG OFF INDICATOR

  1.  Replace the front passenger air bag off indicator.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.AIR BAG DIAGNOSIS SENSOR UNIT

  1.  Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B14XX air bag diagnosis sensor unit
Description DTC B1XXX AIR BAG DIAGNOSIS SENSOR UNIT The air bag diagnosis sensor unit will run self diagnostics when the ignition switch is turned ON. It has the potential to set many diagnostic ...

B142A ignition voltage
Description DTC B142A IGNITION VOLTAGE Ignition voltage is supplied to the air bag diagnosis sensor unit when the ignition is in the ON position. The air bag diagnosis sensor unit will monitor fo ...

Other materials:

P0962 pressure control solenoid A
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0962 PC SOLENOID A (Pressure Control Solenoid A Control Circuit Low) When all of the following conditions are satisfied and this state is maint ...

C1105, C1106, C1107, C1108 wheel sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1105 RR RH SENSOR-2 When distance between rear wheel sensor RH and rear wheel sensor RH rotor is large.  When installation of rear whe ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-49286) Drift and Pull gauge Measuring drift and pull Commercial Service Tool Tool name ...

© 2014-2025 Copyright www.nirogue.com