Nissan Rogue Service Manual: P2119 electric throttle control actuator
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting condition | |
| P2119 | ETC ACTR-B1 (Throttle actuator control throttle body range/performance) | A | Electric throttle control actuator does not function properly due to the return spring malfunction. |
| B | Throttle valve opening angle in fail-safe mode is not in specified range | ||
| C | ECM detect the throttle valve is stuck open. | ||
POSSIBLE CAUSE
Electric throttle control actuator
FAIL-SAFE
Traveling control mode (Engine output control)
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON.
- Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B
- Turn ignition switch ON and wait at least 1 second.
- Set selector lever to D position and wait at least 3 seconds.
- Set selector lever to P position.
- Turn ignition switch OFF and wait at least 10 seconds.
- Turn ignition switch ON and wait at least 1 second.
- Set selector lever to D position and wait at least 3 seconds.
- Set selector lever to P position.
- Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
- Check DTC.
Is DTC detected? YES >> Proceed to EC-438, "Diagnosis Procedure".
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
- Turn ignition switch ON and wait at least 1 second.
- Set selector lever to D position and wait at least 3 seconds.
- Set selector lever to P position.
- Start engine and let it idle for 3 seconds.
- Check DTC.
Is DTC detected? YES >> Proceed to EC-438, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
- Remove the intake air duct. Refer to EM-24, "Exploded View".
- Check if foreign matter is caught between the throttle valve and the housing.
Is the inspection result normal? YES >> Replace electric throttle control actuator. Refer to EM-26, "Removal and Installation".
NO >> Remove the foreign matter and clean the electric throttle control actuator inside, then perform throttle valve closed position learning. Refer to EC-140, "Work Procedure".
P2118 throttle control motor
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2118
ETC MOT-B1
(Throttle actuator control motor ...
P2122, P2123 APP sensor
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P2122
APP SEN 1/CIRC
(Throttle/pedal position sens ...
Other materials:
DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT
Description
Refer to LAN-8, "System Description".
DTC Logic
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps
during a repair. Confirm
that there are actual CAN diagnostic symptoms and a present DTC by p ...
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT
PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
Sensor maintenance
Sensor maintenance
The distance sensor for the FCW system A is
located behind the front bumper.
To keep the FCW system operating properly, be
sure to observe the following:
Always keep the sensor area of the front
bumper clean.
Do not strike or damage the areas around
...
