Nissan Rogue manuals

Nissan Rogue Service Manual: Basic inspection

Nissan Rogue Service Manual / Electrical & power control / Body Control System / Without intelligent key system / Basic inspection

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description

BEFORE REPLACEMENT

When replacing BCM, save or print current vehicle specification with CONSULT configuration before replacement.

NOTE: If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replacing BCM.

AFTER REPLACEMENT

CAUTION:

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Procedure

1.SAVING VEHICLE SPECIFICATION (BCM)

CONSULT

Enter "Re/Programming, Configuration" and perform “Before Replace ECU” to save or print current vehicle specification.

NOTE: If “Before Replace ECU” cannot be used, use the "After Replace ECU" or "Manual Configuration" after replacing BCM.

>> GO TO 2.

2.SAVING VEHICLE SPECIFICATION (CAN GATEWAY)

CONSULT

Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to LAN-75, "CONSULT Function".

NOTE: If “READ CONFIGURATION” cannot be used, use the “WRITE CONFIGURATION - Manual selection” after replacing BCM.

>> GO TO 3.

3.REPLACE BCM

Replace BCM. Refer to BCS-135, "Removal and Installation".

>> GO TO 4.

4.WRITING VEHICLE SPECIFICATION (BCM)

CONSULT

  1.  Enter "Re/Programming, Configuration".
  2.  If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle specification. Refer to BCS-121, "CONFIGURATION (BCM) : Work Procedure".
  3. If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configuration" to write vehicle specification. Refer to BCS-121, "CONFIGURATION (BCM) : Work Procedure".

>> GO TO 5.

5.INITIALIZE BCM (NATS)

Perform BCM initialization. (NATS)

>> GO TO 6.

6.WRITING VEHICLE SPECIFICATION (CAN GATEWAY FUNCTION)

CONSULT

Perform “WRITE CONFIGURATION – Config file” or “WRITE CONFIGURATION – Manual selection” to write vehicle specification. Refer to LAN-77, "Work Procedure".

>> Work End.

CONFIGURATION (BCM)

CONFIGURATION (BCM) : Description

Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.

Configuration has three functions as follows

Function

Function
"Before Replace ECU"
  • Reads the vehicle configuration of current BCM.
  •  Saves the read vehicle configuration.
"After Replace ECU" Writes the vehicle configuration with manual selection.
"Select Saved Data List" Writes the vehicle configuration with saved data.

CAUTION:

CONFIGURATION (BCM) : Work Procedure

1.WRITING MODE SELECTION

CONSULT

Select “Reprogramming, Configuration” of BCM.

When writing saved data>>GO TO 2.

When writing manually>>GO TO 3.

2.PERFORM “SAVED DATA LIST”

CONSULT

Automatically “Operation Log Selection” window will display if “Before Replace ECU” was performed. Select applicable file from the “Save Data List” and press “Confirm”.

>> Work End.

3.PERFORM “AFTER REPLACE ECU” OR “MANUAL CONFIGURATION”

CONSULT

  1.  Select “After Replace ECU” or “Manual Configuration”.
  2. Identify the correct model and configuration list. Refer to BCS-122, "CONFIGURATION (BCM) : Configuration List".
  3. Confirm and/or change setting value for each item.

    CAUTION: Thoroughly read and understand the vehicle specification. ECU control may not operate normally if the setting is not correct.

  4. Select “Next”.

    CAUTION: Make sure to select “Next”, confirm each setting value and press “OK” even if the indicated configuration of brand new BCM is same as the desirable configuration. If not, configuration which is set automatically by selecting vehicle model cannot be memorized.

  5.  When "Completed", select "End".

>> GO TO 4.

4.OPERATION CHECK

Confirm that each function controlled by BCM operates normally.

>> Work End.

CONFIGURATION (BCM) : Configuration List

CAUTION: Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal control of ECU.

Configuration List

⇔: Items which confirm vehicle specifications

SHIPPING MODE CANCEL OPERATION

Work Procedure

1.SHIPPING MODE CANCEL OPERATION

  1.  Turn ignition switch OFF.
  2.  Push in (switch on) the extended storage fuse switch. Refer to PG-73, "How To Check".
  3.  Turn ignition switch ON.
  4.  Turn ignition switch OFF and wait at least 2 seconds.

>> GO TO 2.

2.SHIPPING MODE CANCEL CHECK

  1.  Turn ignition switch ON.
  2.  Check that extended storage fuse warning message is not displayed on information display.

>> Work End.

Wiring diagram
BCM Wiring Diagram ...

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description Refer to LAN-8, "System Description". DTC Logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perh ...

Other materials:

Operating range
Operating range The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 1 . When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key op ...

P0848 transmission fluid pressure SEN/SW B
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0848 FLUID PRESS SEN/SW B (Transmission Fluid Pressure Sensor/Switch B Circuit Low) When all of the following conditions are satisfied and this sta ...

P0132 A/F sensor 1
DTC Description DTC DETECTION LOGIC To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal is not inordinately high. DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0132 A/F S ...

© 2014-2025 Copyright www.nirogue.com