Nissan Rogue Service Manual: B1431 seat belt pre-tensioner

Nissan Rogue Service Manual / Restraints / SRS Airbag Control System / DTC/circuit diagnosis / B1431 seat belt pre-tensioner

DTC Logic

DTC DETECTION LOGIC

CONSULT name	DTC	DTC detecting condition	Repair order
FRONT PRE-TEN RH CIRCUIT [OPEN]	B1431	RH seat belt pre-tensioner circuit is open.	Refer to SRC-61, "Diagnosis Procedure"
FRONT PRE-TEN RH CIRCUIT [VB-SHORT]		RH seat belt pre-tensioner circuit is shorted to a power supply circuit.
FRONT PRE-TEN RH CIRCUIT [GND-SHORT]		RH seat belt pre-tensioner circuit is shorted to ground.
FRONT PRE-TEN RH CIRCUIT [SHORT]		RH seat belt pre-tensioner circuits are shorted to each other.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-61, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-61, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode.

Is the DTC detected? YES >> Refer to SRC-61, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Check the harness connector for the following:

Visible damage to connector or terminal
Loose terminal
Poor connection

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

Visible damage: Replace the harness.
Loose terminal: Secure the terminal.
Poor connection: Secure the connection.

2.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.AIR BAG DIAGNOSIS SENSOR UNIT

Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.SEAT BELT PRE-TENSIONER RH

Replace the seat belt pre-tensioner RH. Refer to SR-28, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B1430 seat belt pre-tensioner

DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order FRONT PRE-TEN LH CIRCUIT [OPEN] B1430 Front LH seat belt pre-ten ...

B1428 seat belt buckle switch IH

Description DTC B1428 SEAT BELT BUCKLE SWITCH LH The air bag diagnosis sensor unit monitors the seat belt buckle switch LH status. If the control unit detects an open or short condition in the ci ...

Other materials:

Removal and installation
AWD CONTROL UNIT Exploded View 1 AWD control unit : Vehicle front : N·m (kg-m, in-lb) Removal and Installation REMOVAL Remove luggage side lower finisher (LH). Refer to INT-33, "Exploded View". Disconnect AWD control unit harness connector. Remove AWD ...

Liquid Gasket
REMOVAL OF LIQUID GASKET SEALING After removing the bolts and nuts, separate the mating surface and remove the liquid gasket using Tool (A). Tool Number : KV10111100 (J-37228) CAUTION: Be careful not to damage the mating surfaces. In areas where the cutter is difficult to use, u ...

Fuel-filler door
Opener operation Opener operation The fuel-filler lid release is located below the instrument panel. To open the fuel-filler lid, pull the release. To lock, close the fuel-filler lid securely. Fuel-filler cap WARNING Gasoline is extremely flammable and highly explosive ...