Nissan Rogue manuals

Nissan Rogue Service Manual: B0098 front door satellite sensor RH

DTC Logic

DTC DETECTION LOGIC

With CONSULT

CONSULT name

DTC

DTC detecting condition

Repair order

DOOR SATELLITE SENSOR RH [SENSOR FAIL] B0098 Front door satellite sensor RH has malfunctioned. Refer to SRC-72, "Diagnosis Procedure".
DOOR SATELLITE SENSOR RH [COMM FAIL] Front door satellite sensor RH communication error.
DOOR SATELLITE SENSOR RH [DISCONNECT] Front door satellite sensor RH is disconnected.
DOOR SATELLITE SENSOR RH [UNMATCH] Front door satellite sensor RH is out of specification.
DOOR SATELLITE SENSOR RH [GND-SHORT] Front door satellite sensor RH circuit is shorted to ground.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-72, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-72, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

  1.  Turn ignition switch ON.
  2.  Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-72, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Recheck SRS after each replacement.

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

NOTE: All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

2.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

  1.  Reconnect all harness connectors.
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.FRONT DOOR SATELLITE SENSOR LH

  1.  Replace the front door satellite sensor LH. Refer to SR-24, "Removal and Installation".
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.AIR BAG DIAGNOSIS SENSOR UNIT

  1.  Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
  2.  Turn ignition switch ON.
  3.  Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B0093 front door satellite sensor LH
DTC Logic DTC DETECTION LOGIC With CONSULT CONSULT name DTC DTC detecting condition Repair order DOOR SATELLITE SENSOR LH [SENSOR FAIL] B0093 Front ...

B0091 front side air bag satellite sensor LH
Description DTC B0091 FRONT SATELLITE SENSOR LH The front side air bag satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the front ...

Other materials:

C1121, C1123, C1125, C1127 ABS out valve system
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1121 FR LH OUT ABS SOL When a malfunction is detected in front LH ABS OUT valve. Harness or connector  ABS actuator and electric unit (control u ...

Key interlock cable
Exploded View Key cylinder  Clip  Key interlock cable  Shift selector assembly Removal and Installation REMOVAL CAUTION: Always apply the parking brake before performing removal and installation.  Move shift selector to the “N” position.  Remo ...

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description Refer to LAN-8, "System Description". DTC Logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm that there are actual CAN diagnostic symptoms and a present DTC by p ...

© 2014-2020 Copyright www.nirogue.com