Nissan Rogue Service Manual: B0094 crash zone sensor

Nissan Rogue Service Manual / Restraints / SRS Airbag Control System / DTC/circuit diagnosis / B0094 crash zone sensor

DTC Logic

DTC DETECTION LOGIC

CONSULT name	DTC	DTC detecting condition	Repair order
CRASH ZONE SENSOR [SENSOR FAIL]	B0094	Crash zone sensor has malfunctioned.	Refer to SRC-68, "Diagnosis Procedure".
CRASH ZONE SENSOR [COMM FAIL]		Crash zone sensor communication error.
CRASH ZONE SENSOR [DISCONNECT]		Crash zone sensor is disconnected
CRASH ZONE SENSOR [UNMATCH]		Crash zone sensor is out of specification.
CRASH ZONE SENSOR [GND-SHORT]		Crash zone sensor circuit is shorted to ground.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-68, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-68, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-68, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

Visible damage to connector or terminal
Loose terminal
Poor connection

NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

Visible damage: Replace the harness.
Loose terminal: Secure the terminal.
Poor connection: Secure the connection.

2.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.CRASH ZONE SENSOR

Replace the crash zone sensor. Refer to SR-22, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.AIR BAG DIAGNOSIS SENSOR UNIT

Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B1429 seat belt buckle switch RH

Description DTC B1429 SEAT BELT BUCKLE SWITCH RH The air bag diagnosis sensor unit monitors the seat belt buckle switch RH status. If the control unit detects an open or short condition in the ci ...

B0093 front door satellite sensor LH

DTC Logic DTC DETECTION LOGIC With CONSULT CONSULT name DTC DTC detecting condition Repair order DOOR SATELLITE SENSOR LH [SENSOR FAIL] B0093 Front ...

Other materials:

Front door finisher
Exploded View Front door Front door pull handle bracket Front door pull handle Front power window switch (RH) finisher Front door inside handle finisher Front door finisher Clip Pawl REMOVAL NOTE: LH shown, RH similar. Release pawls using a suitable tool (A) from ...

O/D off indicator lamp
Component Function Check 1.CHECK O/D OFF INDICATOR LAMP FUNCTION Check O/D OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON. Is the inspection results normal? YES >> INSPECTION END NO >> Go to TM-181, "Diagnosis Procedure". Diagnosis Pro ...

Circuit inspection
DESCRIPTION In general, testing electrical circuits is an easy task if it is approached in a logical and organized method. Before beginning it is important to have all available information on the system to be tested. Also, get a thorough understanding of system operation. Then y ...