Nissan Rogue (T33) 2021-Present Service Manual: U2a05-88 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / U2a05-88 Can Comm Circuit

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U2A05-88

Comm Bus Off ITS4-FD

(Communication Bus Off Intelligent Transport System4-FD) 		Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold Sonar control unit cannot communicate CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

ー

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check DTC.

Is DTC U2A05-88 detected?

YES>>

Proceed to Diagnosis Procedure .

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2A05-88 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

    U214f-57 Mac Comm Error (ipdm E/r)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U214F-57 CAN comm err (IPDM E/R) [Control Area Network commu...
    Dtc/circuit Diagnosis. Power Supply and Ground Circuit. Sonar Control Unit
    Sonar Control Unit Diagnosis Procedure CHECK FUSE Check that the following fuse is not blown (open). Power source Fuse No. Capacity ACC power supply #40 10 A Is the fuse blown (...

    Other materials:

    Limites du système de détecteur de collision frontale intelligent
    Illustration A Illustration B Illustration C Illustration D AVERTISSEMENT Les limites du système de détecteur de collision frontale intelligent du Nissan Rogue sont décrites ci-dessous. Le non-respect de ces limites lors de la conduite peut entraîner des blessures gr ...

    Dtc/circuit Diagnosis. U2152-87 Can Comm Err (adas Control Unit 2)
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped ...

    Removal and Installation. Moonroof Switch Assembly
    Removal and Installation REMOVALRemove map lamp finisher. Removal and Installation Disengage moonroof switch assembly fixing pawls using a remover tool, and then remove moonroof switch assembly from map lamp finisher . : Pawl INSTALLATIONInstall in the reverse order of removal. ...