Nissan Rogue (T33) 2021-Present Service Manual: U2675-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2675-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2675 87 CAN communication error (around view monitor control unit) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from around view monitor control unit.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • Around view monitor control unit

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2675-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2675-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK AROUND VIEW MONITOR CONTROL UNIT SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “AROUND VIEW MONITOR”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “AROUND VIEW MONITOR”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK AROUND VIEW MONITOR CONTROL UNIT SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect around view monitor control unit harness connector.

  3. Check around view monitor control unit harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect around view monitor control unit harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2675-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2675 83 CAN communication error (around view monitor control unit) Diagnosis condition ...
    U2a03-88 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2A03 88 Communication Bus Off CH-FD 1 Diagnosis condition When ignition switch is ON. S...

    Other materials:

    C1f76-49 Steering Angle Sensor
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F76 49 Steering angle sensor (Steering angle sensor) Diagnosis condition When engine is running When AEB system is ...

    P02cd Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CD 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) Diagnosis condition Engine running During injector ...

    Removal and Installation. Tire Pressure Sensor
    Exploded View Screw Tire pressure sensor Valve Valve core Valve cap : Comply with the assembly procedure when tightening. Refer to Removal and Installation. : N·m (kg-m, in-lb) : Always replace after every disassembly. Removal & Install ...