Nissan Rogue (T33) 2021-Present Service Manual: U2143-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2143-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2143 83 CAN communication error (VCM) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold ECM in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • ECM

FAIL-SAFE

The following functions are suspended.

  • Intelligent trace control function

  • Active ride control function

  • Automatic brake hold function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2143-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2143-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK ECM SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “ENGINE”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “ENGINE”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK ECM SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check ECM harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect ECM harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U2141-57 Mac Comm Error (tcm)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2141 57 CAN communication error (TCM) Diagnosis condition — Signal (terminal) — Thr...
    U2143-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2143 87 CAN communication error (VCM) Diagnosis condition When ignition switch is ON. S...

    Other materials:

    Heated steering wheel
    Example Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light A will illuminate once the system is active. If the steering wheel surface temperature is below 86–104ºF (30–40ºC), the system will automatically heat the wheel and cycle o ...

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...