Nissan Rogue (T33) 2021-Present Service Manual: Symptom Diagnosis :: Combination Switch System Symptoms
Symptom Table
-
Select “Data monitor” of CONSULT to check for any malfunctioning item.
-
Check that the data monitor display switches in conjunction with the combination switch operation.
-
If there is a switch whose display does not change, specify the applicable combination switch circuit (INPUT 1 - 6 and OUTPUT 1 - 6) using the combination switch circuit confirmation table for the circuit used for that switch.
NOTE:
Since combination switch circuit is share with multiple switches, if the switches used other than the defective switch are normal, the combination switch circuit can be determined to be normal.
Example: If the circuit used for the switch corresponds to INPUT 1 and OUTPUT 2 of the combination switch circuit, but the other switches that use the INPUT 1 circuit are normal, it is determined that the INPUT 1 circuit is normal and inspection OUTPUT 2 circuit. If other switches that use OUTPUT 2 circuit are normal, the combination switch circuit (INPUT 1 and OUTPUT 2) is determined to be normal, and it can be determined that the combination switch is defective.
Circuit used: ×
Combination switch circuit confirmation table Data monitor item Combination switch circuit INPUT 1 INPUT 2 INPUT 3 INPUT 4 INPUT 5 INPUT 6 OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT 6 Check diode 1 × × High beam switch × × Passing switch × × Front fog switch × × INT volume 1 × × Check diode 2 × × Low beam switch × × AUTO light switch* × × Tail lamp switch × × Front washer switch × × Rear washer switch × × Check diode 3 × × Turn signal LH × × Turn signal RH × × Front wiper LO × × Front wiper HI × × Front wiper INT × × Check diode 4 × × Light OFF switch × × INT volume 2 × × INT volume 3 × × Rear wiper INT × × Rear wiper ON × × Check diode 5 × × Front wiper OFF × × Front wiper MIST × × High beam assist × × Check diode 6 × × NOTE:
*: This item is displayed, but cannot be monitored (for Canada models).
-
Identify the possible malfunctioning part from combination switch circuit confirmation table and inspection or replace it.
Possible malfunction part / Symptom Inspection / Replace Some data monitor displays do not switch There is a malfunction with either of the combination switch INPUT circuit Inspect the combination switch input circuit applicable to the malfunctioning part. Refer to Diagnosis Procedure. There is a malfunction with either of the combination switch OUTPUT circuit Inspect the combination switch output circuit applicable to the malfunctioning part. Refer to Diagnosis Procedure. It is not applicable to any of the combination switch INPUT circuit and OUTPUT circuit Replace combination switch. Refer to Removal and Installation.
If the data monitor display does not switch for a specific switch, the corresponding switch has a malfunction.All data monitor displays do not switch Replace BCM. Refer to Removal and Installation. All data monitor displays switch Check intermittent incident. Refer to Intermittent Incident.
Other materials:
Symptom Diagnosis. Front Passenger Side Power Window Does Not Operate
When Both Power Window Main Switch and Front Power Window Switch (passenger Side) Are Operated
Diagnosis Procedure
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY AND GROUND CIRCUIT
Check front power window switch (passenger side) power supply and ground circuit.
Refer to Diagnosis ...
Informations de base
Exemple
Le système de sonar du Nissan Rogue émet des signaux sonores afin d’informer le conducteur de la présence d’obstacles autour du véhicule. Cette détection est assurée par des capteurs sonar installés dans les pare-chocs avant et arrière.
Lorsque le système de sonar est ac ...
Removal and Installation. Emblem
Exploded view
1.
Emblem A
2.
Emblem B
3.
Emblem C (if equipped)
4.
Emblem D (if equipped)
Removal and Installation
REMOVALRemove emblem from the panel while warming using an industrial dryerCAUTION:
Remove the panel so as not to damage ...