Nissan Rogue manuals

Nissan Rogue Service Manual: P2610 ECM internal timer

Description

This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state of engine cooling at an engine start.

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P2610 ECM/PCM INTERNAL ENG OFF TIMER (ECM/PCM internal engine off timer performance)
  • ECM internal engine off timer is malfunctioning.
  •  The time calculated by ECM based on a descent allowance of engine coolant temperatures during ignition switch OFF is extremely shorter than the time counted by the Engine internal OFF timer.

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.INSPECTION START

It is necessary to erase permanent DTC? YES >> GO TO 4.

NO >> GO TO 2.

2.PRECONDITIONING

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is 12 V or more under ignition switch OFF condition.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE-I

  1.  Turn ignition switch ON and wait at least 190 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-454, "Diagnosis Procedure".

NO >> INSPECTION END

4.PRECONDITIONING

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

>> GO TO 5.

5.PERFORM DTC CONFIRMATION PROCEDURE-I

  1.  Turn ignition switch ON and wait at least 190 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-454, "Diagnosis Procedure".

NO >> GO TO 6.

6.PERFORM DTC CONFIRMATION PROCEDURE-II

CAUTION: To start this self-diagnosis, the conditions listed bellow are required to be satisfied. Perform the following steps to satisfy the conditions.

NOTE: This self-diagnosis is not performed if the distance traveled is extremely short.

  1.  Turn ignition switch ON.
  2.  Start engine and warm it up to normal operating temperature.
  3.  Turn ignition switch OFF and soak the vehicle for at least 12 hours.

CAUTION:

  1. Turn ignition switch ON and wait at least 190 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-454, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK SELF-DIAGNOSTIC RESULT

check that DTCs related to the fuel system and the cooling system are not detected.

Is the inspection result normal? YES >> Check the DTC. Refer to EC-67, "CONSULT Function".

NO >> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Erase DTC.
  2.  Perform DTC Confirmation Procedure again. Refer to EC-453, "DTC Description".

Is the 1st trip DTC P2610 displayed again? YES >> Replace ECM. Refer to EC-499, "Removal and Installation".

NO >> INSPECTION END

P2138 APP sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2138 APP SENSOR (Throttle/pedal position sensor/s ...

Brake pedal position switch
Component Function Check 1.CHECK BRAKE PEDAL POSITION SWITCH FUNCTION With CONSULT  Turn ignition switch ON.  Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT.   ...

Other materials:

P0524 engine oil pressure
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0524 ENGINE OIL PRESSURE (Engine oil pressure too low) An EOP sensor signal voltage applied to ECM remains lower than the specified value c ...

Driver air bag module
Exploded View Steering wheel Driver air bag module Removal and Installation WARNING:  Before servicing the SRS, turn ignition switch OFF, disconnect both battery terminals then wait at least three minutes.  Always work from the side of driver air bag module. Do no ...

Operating range
Operating range The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch 1 . When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key op ...

© 2014-2023 Copyright www.nirogue.com