Nissan Rogue (T33) 2021-Present Service Manual: P2564 Wastegate Control Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2564 Wastegate Control Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2564 00

TC BOOST CONTROL POSITN SEN A

(Turbocharger boost control position sensor A circuit low) 		Diagnosis condition —
Signal (terminal) —
Threshold ECM detects the following status continuously for 5 seconds or more: A voltage signal transmitted from the wastegate control valve position sensor is 0.50 V or less.
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Wastegate control valve position sensor circuit is open or shorted.)

  • Electric wastegate control actuator

  • Sensor power supply 1 circuit

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect electric wastegate control actuator harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between electric wastegate control actuator harness connector and ground.

    + −

    Voltage

    (Approx.)
    Electric wastegate control actuator
    Connector Terminal
    F95 4 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric wastegate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 2 F71 111 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between electric wastegate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 3 F71 75 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Check the electric wastegate control actuator. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace electric waste gate control actuator. Refer to Component Parts Location.

CHECK WASTEGATE CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between electric waste gate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 4 F71 83 Existed

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

    P2563 Wastegate Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2563 00 TC BOOST CONTROL POSITN SEN A (Turbocharger boost contr...
    P2565 Wastegate Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2565 00 TC BOOST CONTROL POSITN SEN A (Turbocharger boost contr...

    Other materials:

    Brake Warning Lamp
    Component Function Check CHECK BRAKE WARNING LAMP FUNCTION (1) Check that brake warning lamp in combination meter turns ON for approximately 1 second after ignition switch is ON (before engine start). Is the inspection result normal? YES>> GO TO 2. NO>> Refer to Diagnosis Pr ...

    Torque Converter and Converter Housing Oil Seal
    Exploded View 1. Torque converter 2. Converter housing oil seal 3. Transaxle assembly : Always replace after every disassembly. : Apply CVT fluid Disassembly Remove transaxle assembly. Refer to Removal and Installation. Remove torque converter from transaxle as ...

    P06e6 Internal Control Module
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the s ...