Nissan Rogue (T33) 2021-Present Service Manual: P0606 Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0606 Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0606 00

CONTROL MODULE

(Control module processor) 		Diagnosis condition —
Signal (terminal) —
Threshold Malfunction in ECM processor
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

or

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

or

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds.

    CAUTION:

    Never start engine during this procedure.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Start engine.

  2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release the accelerator pedal.

  3. Let the engine idle and wait at least 10 seconds.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Turn ignition switch ON.

  6. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for 3 times. Refer to DTC Description.

Is the 1st trip DTC P0606 displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P0604 Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0604 00 ECM [Internal control module random access memory (RAM)...
    P0607 Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0607 00 ECM (Control module performance) Diagnosis condition Ig...

    Other materials:

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...

    Dtc/circuit Diagnosis. Memory Indicator
    Component Function Check CHECK FUNCTION Push set switch. Check memory indicator operation. When driver seat position is already retained in memory : Illuminated for 5 seconds When driver seat position is not retained in memory : Illuminated for 0.5 second Is the ins ...

    Precautions on seat belt usage
    Wearing your seat belt correctly — sitting upright, positioned well back in the seat, and keeping both feet on the floor — significantly reduces the risk of injury or death in an accident. When used properly, seat belts work together with your Nissan Rogue’s safety systems, including suppleme ...