Nissan Rogue (T33) 2021-Present Service Manual: P050e Cold Start Control

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P050e Cold Start Control

DTC Description

DESCRIPTION

ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.

This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P050E 00

COLD START CONTROL

(Cold start engine exhaust temperature too low) 		Diagnosis condition Engine cold start
Signal (terminal) Engine speed signal and Ingnittion timing signal
Threshold The temperature of the catalyst inlet does not rise to the proper temperature when the engine is started with pre-warming up condition
Diagnosis delay time —

POSSIBLE CAUSE

  • Lack of intake air volume

  • Fuel injection system

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-1

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Select “DATA MONITOR” mode with CONSULT.

  4. Check the indication of “COOLANT TEMP/S”.

With GST

Follow the procedure “With CONSULT” above.

Is the value of “COOLANT TEMP/S” between 15°C (59°F) and 36°C (97°F)?

YES>>

GO TO 4.

NO-1 [If it is below 15°C (59°F)]>>

Warm up the engine until the value of “COOLANT TEMP/S” reaches 15°C (59°F) or more. Retry from step 2.

NO-2 [If it is above 36°C (97°F)]>>

Cool engine down to less than 36°C (97°F). Retry from step 2.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

  1. Set the select lever in N range.

  2. Start the engine and warm up in idle with the value of “COOLANT TEMP/S” between 15°C (59°F) and 40°C (104°F) for more than 15 seconds.

  3. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P050E is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM IDLE AIR VOLUME LEARNING

Refer to Work Procedure.

Is Idle Air Volume Learning carried out successfully?

YES>>

GO TO 3.

NO>>

Follow the instruction of Idle Air Volume Learning.

CHECK Intake system

Check for the cause of intake air volume lacking. Refer to the following.

  • Crushed intake air passage

  • Intake air passage clogging

  • Clogging of throttle body

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace malfunctioning part

CHECK FUEL INJECTION SYSTEM FUNCTION

Perform DTC Confirmation Procedure for DTC P0171. Refer to DTC Description.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Refer to DTC Diagnosis Procedure for DTC P0171.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC Confirmation Procedure. Refer to DTC Description.

Is the 1st trip DTC P050E displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P050b Cold Start Control
    DTC Description DESCRIPTIONECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.This control promotes the activation of three ...
    P051c Crankcase Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P051C 00 Crankcase Pressure Sensor "A" Circuit Low (Crankcase Pr...

    Other materials:

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...

    B2721-11 Center Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2721-11 CENTER SENSOR [RL] (Center sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH inner Threshold ...