Nissan Rogue (T33) 2021-Present Service Manual: P02d0 Fuel Injector

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P02d0 Fuel Injector

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P02D0 00

CYL3 INJECTOR OFFSET LEARNING

(Cylinder 3 Fuel Injector "A" Offset Learning At Min Limit) 		Diagnosis condition

  • Engine running

  • During injector offset learning
Signal —
Threshold

  • Injector valve opening delay time less than threshold.

  • Injector valve closing delay time more than threshold.

  • Injector offset correction value less than threshold.

  • Injector valuse closing timing is couild not be found.
Diagnosis delay time —

POSSIBLE CAUSE

  • ECM

  • Fuel injector (Cylinder 3)

  • Harness or connectors (Fuel injector circuit is open or shorted.)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P02D0 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-1

With CONSULT

  1. Turn ignition switch ON.

  2. Select “COOLANT TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

  3. Check the following condition;

    COOLANT TEMP/S : 5 – 40°C (41 – 104°F)

Is the condition satisfied?

YES>>

GO TO 4.

NO>>

  1. Satisfy the condition.

  2. Retry from step 2.

PERFORM DTC CONFIRMATION PROCEDURE-2

With CONSULT

  1. Start the engine.

  2. Select “COOLANT TEMP/S” in “DATA MONITOR” mode of “ENGNE” using CONSULT.

  3. Maintain the following condition for 20 seconds or more at idle.

    COOLANT TEMP/S : 60°C (140°F) or more

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 5.

PERFORM DTC CONFIRMATION PROCEDURE-3

With CONSULT

  1. Perform “Fuel injector offset learning” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.

  2. Maintain the following condition for 10 seconds.

    Electrical load signal

    • A/C switch: ON

    • Electric load: ON (Lights, heater fan & rear window defogger)
    Engine speed 2,000 - 3,000 rpm

  3. Check DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P02D0 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK FUEL INJECTOR

  1. Check fuel injector. Refer to Component Function Check.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check DTC.

Is the DTC P02D0 displayed again?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE FUEL INJECTOR

  1. Replace fuel injector at cylinder 3. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check DTC.

Is the DTC P02D0 displayed again?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE ECM

Replace ECM. Refer to ECM : Removal & Installation.

>>

INSPECTION END

    P02cf Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CF 00 CYL2 INJECTOR OFFSET LEARNING (Cylinder 2 Fuel Injector...
    P02d1 Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02D1 00 CYL3 INJECTOR OFFSET LEARNING (Cylinder 3 Fuel Injector...

    Other materials:

    Dtc/circuit Diagnosis. B0073-09 Pre-Ten Rear Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0073-09 PRE-TEN REAR LH (Second Row Left Seat Belt Pretensioner Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Rear ...

    Preparation
    Special Service Tools The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name Description (NI-39570) Chassis ear Locates the noise (NI-50397) Squeak and Rattle Kit Repairs the cause o ...

    Dtc/circuit Diagnosis. C18d6-09 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18D6 09 Backup power supply unit 1 Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunction is de ...