Nissan Rogue (T33) 2021-Present Service Manual: P0046 Wastegate Control Motor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0046 Wastegate Control Motor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0046 00

TC/SC BOOST CONTROL A

(Turbocharger/supercharger boost control A circuit range/performance) 		Diagnosis condition —
Signal (terminal) —
Threshold

When the following conditions are detected due to a malfunction in electric wastegate actuator motor:

  • Motor drive duty is 100% or more.

  • The difference between target stroke and actual stroke is 1.95mm (0.0768 in) or more.
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Electric wastegate control motor circuit is open or shorted.)

  • Electric wastegate control actuator

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P0046 is displayed with DTC P2562 or P2566, first perform the trouble diagnosis for DTC P2562 or P2566.

Is 1st trip DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is between more than 11 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Start the engine and warm it up to nomal operating temperature.

  3. Check 1st trip DTC. (If actuator motor is stuck on the valve closing side, 1st trip DTC is detected during the above procedure. If 1st trip DTC is not detected, actuator motor may be stuck on the valve opening side. In this case, follow the instruction below.)

  4. Drive the Nissan Ariya vehicle and accelerate from 20km/h (13 MPH) to 80km/h (50 MPH) within 10 seconds.

    CAUTION:

    Always drive at safe speed.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0046 is displayed with DTC P2562 or P2566, first perform the trouble diagnosis for DTC P2562 or P2566.

Is 1st trip DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric wastegate control actuator harness connector and ECM harness connector.

  3. Check the continuity between electric wastegate control actuator harness connector and ECM harness connector.

    Electric wastegate control actuator ECM Continuity
    Connector Terminal Connector Terminal
    F95 2 F71 111 Existed
    4 83

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR

Check the electric wastegate control actuator. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace electric wastegate control actuator.

    P0036 Ho2s2 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0036 00 HO2S1 HTR (B1) (HO2S Heater Control Circuit Bank 1 Sens...
    P0053 A/f Sensor 1 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0053 00 HO2S1 HTR B1 (HO2S heater resistance bank 1 sensor 1) D...

    Other materials:

    Can Fundamental. Basic Inspection. Diagnosis and Repair Work Flow
    Diagnosis and Repair Work Flow Trouble Diagnosis Flow Chart DESCRIPTIONDETAIL OF TROUBLE DIAGNOSIS FLOW CHARTINTERVIEW WITH CUSTOMER Interview with the customer is important to detect the root cause of CAN communication system errors and to understand Nissan Ariya vehicle condition and sympto ...

    Brake Warning Lamp
    Component Function Check CHECK BRAKE WARNING LAMP FUNCTION (1) Check that brake warning lamp in combination meter turns ON for approximately 1 second after ignition switch is ON (before engine start). Is the inspection result normal? YES>> GO TO 2. NO>> Refer to Diagnosis Pr ...

    Removal and Installation. 12v Battery Current Sensor
    Exploded View : 12V battery current sensor : Harness connector : N·m (kg-m, in-lb) Removal and Installation REMOVALDisconnect the 12V battery current sensor connector . Remove negative cable mounting nut , and then remove the negative cable . Loosen 12V battery cu ...