Nissan Rogue Service Manual: Easy fill tire alert does not activate
Description
The easy fill tire alert does not function while inflating a tire when the select lever position is in P-range with the power switch ON or with the vehicle set to READY.
NOTE:
- After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function.
- If there is no response for approximately 15 seconds or more
after inflating the tires, cancel the use of the
easy fill tire alert function or move the vehicle approximately 1 m (3.2 ft)
backward or forward to try again.
The air filler pressure may be weak or out of service area.
- For easy fill tire alert, Refer to WT-9, "Easy Fill Tire Alert Function".
Diagnosis Procedure
1. LOCATION CHANGE
Move the vehicle to other area and repeat the procedure of the easy fill tire alert function. Refer to WT-9, "Easy Fill Tire Alert Function".
Is the function normal? YES >> Normal (the easy fill tire alert may not operate, depending on reception condition.) NO >> GO TO 2.
2.PERFORM BCM SELF-DIAGNOSIS
With CONSULT
Perform “self-diagnosis” for “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected? YES >> Perform diagnosis for detected DTC. Refer to BCS-48, "DTC Index".
NO >> GO TO 3.
3.CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Does the hazard warning lamp blink? YES >> GO TO 4.
NO >> Perform diagnosis for the hazard warning lamp. Refer to EXL-55, "Wiring Diagram".
4.PERFORM ELECTRIC SHIFT CONTROL MODULE SELF-DIAGNOSIS
With CONSULT
Perform “self-diagnosis” for “SHIFT”.
Is any DTC detected? YES >> Perform diagnosis for detected DTC. Refer to BCS-48, "DTC Index".
NO >> GO TO 5.
5.CHECK HORN OPERATION
Check horn operation. Refer to HRN-3, "Wiring Diagram".
Is the operation normal? YES >> GO TO 6.
NO >> Repair or replace malfunctioning components.
6.PERFORM SELF-DIAGNOSIS
With CONSULT
- Drive for 10 minutes at a speed of 40 km/h (25 MPH) or more.
CAUTION: Total time driving at a speed of 40 km/h (25 MPH) or more must be 10 minutes.
- Stop the vehicle.
- Perform “self-diagnosis” for “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected? YES >> Perform diagnosis for detected DTC. Refer to BCS-48, "DTC Index".
NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key System) or BCS- 135, "Removal and Installation" (without Intelligent Key System).
ID registration cannot be completed
Description
The ID of the tire pressure sensor installed in each wheel cannot be
registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring ...
Noise, vibration and harshness (NVT) troubleshooting
NVH Troubleshooting Chart
Use the chart below to find the cause of the symptom. If necessary, repair or
replace these parts.
×: Applicable ...
Other materials:
Installing front license plate
Installing front license plate
Use the following steps to mount the front license
plate:
Before mounting the license plate, confirm that
the following parts are enclosed in the plastic
bag:
License plate bracket
License plate bracket (J-nut) screws x 2
License plat ...
System
System Description
When the vehicle has reached a speed of 40 km/h (25 MPH) or greater, the BCM
receives a signal transmitted
from the tire pressure sensors installed in each wheel. If the BCM detects low
inflation pressure or a system
malfunction, it sends a signal to the combination meter v ...
Operation
AUTOMATIC SPEED CONTROL DEVICE (ASCD)
AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Switch Name and Function
SWITCHES AND INDICATORS
A On the combination meter
B On the steering wheel
1 CRUISE indicator
2 SET indicator
3 CANCEL switch
4 ACCEL/RES switch
5 COAST/SET switch
6 ASCD MAIN sw ...
