Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C18e1-19 Motor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake System / Dtc/circuit Diagnosis :: C18e1-19 Motor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
C18E1 19 Motor Diagnosis condition When Ignition switch is ON.
Signal (terminal) —
Threshold When the voltage difference between both ends of the motor resistor is 2.0 V or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven Intelligent Brake Unit

  • Electrically-driven Intelligent Brake Unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always Ignition switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

CAUTION:

Never operate the Nissan Ariya vehicle.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-19" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer toIntermittent Incident .

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Ignition switch OFF to ON without depressing the brake pedal.

  3. Ignition switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  5. Ignition switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Ignition switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  9. Ignition switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

GO TO 3.

NO>>

Inspection End.

CHECK CONNECTOR TERMINALS

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect Electrically-driven Intelligent Brake Unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Ignition switch OFF to ON without depressing the brake pedal.

  4. Ignition switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  6. Ignition switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Ignition switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  10. Ignition switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

GO TO 5.

NO>>

Inspection End.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Ignition switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect Electrically-driven Intelligent Brake Unit harness connector.

  5. Check the Electrically-driven Intelligent Brake Unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Ignition switch OFF to ON without depressing the brake pedal.

  2. Ignition switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  4. Ignition switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Ignition switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

    CAUTION:

    Never operate the Nissan Ariya vehicle.

  8. Ignition switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

Replace the Electrically-driven Intelligent Brake Unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C18e1-18 Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18E1 18 Motor Diagnosis condition When Ignition switch is ON. Signal (terminal) — Thr...
    Dtc/circuit Diagnosis. C18e1-49 Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18E1 49 Motor 1 Diagnosis condition When Ignition switch is ON. Signal (terminal) — T...

    Other materials:

    Dtc/circuit Diagnosis. B242a-98 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-98 Closure motor (Closure motor) Diagnosis condition When back door closure function operate Signal (terminal) — Threshold When thermal prot ...

    Dtc/circuit Diagnosis. C18d6-09 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18D6 09 Backup power supply unit 1 Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunction is de ...

    C1213-A3 Control Unit Power Supply
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1213-A3 BATTERY VOLTAGE (Battery voltage) Diagnosis condition Ignition switch: ON Signal Battery power supply signal (terminal #6) Threshold Battery po ...