Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1624-00 Signal Connector

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C1624-00 Signal Connector

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1624 00

Signal connector

(Signal connector) 		Diagnosis condition When engine running.
Signal (terminal) —
Threshold When a malfunction is detected in power steering control module signal connector.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication line

  • Power steering control module

FAIL-SAFE

Slowly reducing assistance state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C1624-00” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK TERMINALS AND HARNESS CONNECTORS

Check power steering control module terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, or terminal.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF to ON.

  2. Erase self diagnosis results for “EPS/Direct Adaptive Steering 3”.

  3. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  4. Ignition switch OFF.

  5. Get out of the Nissan Ariya vehicle and close all doors.

  6. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

  7. Ignition switch ON.

  8. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C1624–00” detected?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C1622-86 Bcm System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1622 86 BCM system (Body control module system ) Diagnosis ...
    Dtc/circuit Diagnosis. C1632-86 Steering Angle Sensor System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1632 86 ST angle sensor system (Steering angle sensor syste...

    Other materials:

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...

    P00d2 Ho2s2 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00D2 00 Heated O2 sensor heater B1 sensor 2 (HO2S heater control circuit range/performance bank 1 sensor 2) Diagnosis condition — Signal (terminal) ...