Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C161c-82 Steering Angle Sensor System

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C161c-82 Steering Angle Sensor System

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C161C 82

ST angle sensor system

(Steering angle sensor system) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in steering angle sensor.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication line

  • Steering angle sensor

  • Power steering control module

FAIL-SAFE

Normal state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C161C-82” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF to ON.

  2. Perform self diagnosis for "ABS".

Is any DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK CONNECTOR AND TERMINAL

  1. Ignition switch OFF.

  2. Disconnect steering angle sensor harness connector.

  3. Disconnect power steering control module harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness, connector, or terminal, securely lock the connector.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect steering angle sensor harness connector.

  2. Connect power steering control module harness connector.

  3. Ignition switch OFF to ON.

  4. Erase self diagnosis results for “EPS/Direct Adaptive Steering 3”.

  5. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  6. Ignition switch OFF.

  7. Get out of the Nissan Ariya vehicle and close all doors.

  8. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

  9. Ignition switch ON.

  10. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C161C-82” detected?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Inspection End.

    Dtc/circuit Diagnosis. C161b-86 Abs System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161B 86 ABS system (Anti-lock braking system ) Diagnosis co...
    Dtc/circuit Diagnosis. C161c-83 Steering Angle Sensor System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161C 83 ST angle sensor system (Steering angle sensor syste...

    Other materials:

    Front Wheel Hub and Knuckle
    Exploded View Steering knuckle Splash guard Hub bolt Wheel hub and bearing assembly Disc rotor Wheel hub lock nut : Comply with the installation procedure when tightening. Refer to Removal and Installation. : N·m (kg-m, ft-lb) : Always replace aft ...

    Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses
    Work Flow CUSTOMER INTERVIEWInterview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of customer's comments; Refer to Diagnostic Work ...

    Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTCs ...