Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2f70-02 Stop Lamp

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Security Control System / Dtc/circuit Diagnosis :: B2f70-02 Stop Lamp

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detecting condition
B2F70-02

Stop lamp

(Stop lamp) 		Diagnosis condition When brake pedal is depressed
Signal (terminal)

  • Stop lamp switch 1 signal

  • Stop lamp switch 2 signal
Threshold BCM makes a comparison between stop lamp switch 1 signal and stop lamp switch 2 signal. It judges from their values to detect the malfunctioning circuit 10 consecutive times.
Diagnosis delay time Depress brake pedal 10 times

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is open or shorted)

  • Stop lamp switch

  • Fuse

FAIL-SAFE

—

CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Depress brake pedal 10 times.

  2. Ignition switch ON.

  3. Select “Self diagnosis result” mode of “BCM”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK STOP LAMP SWITCH

CONSULT

  1. Select “Brake switch 1” and “Brake switch 2” in “Data monitor” mode of “BCM [SIGNAL BUFFER]”.

  2. Check “Brake switch 1” and “Brake switch 2” indication under the following condition:

Monitor item Condition Indication
Brake switch 1 Brake pedal Depressed Off
Not depressed On
Brake switch 2 Depressed On
Not depressed Off

Is the indication normal?

YES>>

Stop lamp switch is OK.

NO-1>>

Brake switch 1: GO TO 2.

NO-2>>

Brake switch 2: GO TO 7.

CHECK FUSE

Check that the following fuse is not blown (open).

Signal name Fuse No.
Battery power supply 32 (5 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO>>

GO TO 3.

CHECK STOP LAMP SWITCH SIGNAL-1

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Ignition switch ON.

  4. Check voltage between BCM harness connector and ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E29 (with type B meter) 111 Ground Stop lamp switch 1 ON (brake pedal is not depressed) Battery voltage
    E60 (with type A meter) 116 Stop lamp switch 1 OFF (brake pedal is depressed) 0 V

Is the inspection normal?

YES>>

Inspection End.

NO>>

GO TO 4.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT-1

  1. Ignition switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Ignition switch ON.

  4. Check voltage between stop lamp switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Stop lamp switch
    Connector Terminal
    E38 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-1

  1. Ignition switch OFF.

  2. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switch BCM Continuity
    Connector Terminal Connector Terminal
    E38 3 E29 (with type B meter) 111 Yes
    E60 (with type A meter) 116

  3. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch — Continuity
    Connector Terminal
    E38 3 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp switch. Refer to Exploded View (without ProPILOT ASSIST), or Exploded View (with ProPILOT ASSIST).

CHECK FUSE

Check that the following fuse is not blown (open):

Signal name Fuse No.
Battery power supply 21 (10 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO>>

GO TO 8.

CHECK STOP LAMP SWITCH SIGNAL-2

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check voltage between BCM harness connector and ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E29 (with type B meter) 110 Ground Stop lamp switch 2 ON (brake pedal is depressed) Battery voltage
    E60 (with type A meter) 115 Stop lamp switch 2 OFF (brake pedal is not depressed) 0 V

Is the inspection normal?

YES>>

Inspection End.

NO>>

GO TO 9.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT-2

  1. Disconnect stop lamp switch connector.

  2. Check voltage between stop lamp switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Stop lamp switch
    Connector Terminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT-2

  1. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switch BCM Continuity
    Connector Terminal Connector Terminal
    E38 2 E29 (with type B meter) 110 Yes
    E60 (with type A meter) 115

  2. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch — Continuity
    Connector Terminal
    E38 2 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2f70-01 Stop Lamp
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2F70-01 Stop lamp (Stop lamp) Diagnosis condition When brak...
    Dtc/circuit Diagnosis. B2f71-23 Stop Lamp
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2F71-23 Stop lamp (Stop lamp) Diagnosis condition When brak...

    Other materials:

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...

    C107c-53 Not Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C107C 53 Not configuration (Not configuration) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. Signa ...

    U2e52-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2E52 87 CAN communication error (ADAS control unit) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Not receiving from ADAS c ...