Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2437-12 Spindle Motor Rh

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2437-12 Spindle Motor Rh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2437-12

Spindle motor RH

(Spindle motor right hand) 		Diagnosis condition All times
Signal (terminal) Spindle motor RH signal
Threshold When automatic back door control unit detect power short of spindle motor RH circuit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (spindle motor RH circuit is power short)

  • Automatic back door control unit

  • Spindle unit RH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK SPINDLE MOTOR INPUT SIGNAL

Check signal between spindle unit RH harness connector and ground using oscilloscope.

(+) (–) Condition

Signal

(Reference value)

(Approx.)
Spindle unit RH
Connector Terminal
B73 1 Ground Back door Auto open operation

Auto close operation 0 – 1 V
7 Auto close operation

Auto open operation 0 – 1 V

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK SPINDLE MOTOR CIRCUIT

  1. Disconnect automatic back door control unit connector and spindle unit RH connector.

  2. Check voltage between automatic back door control unit harness connector and ground.

    Automatic back door control unit —

    Voltage

    (Approx.)
    Connector Terminal
    B56 35 Ground 0 V
    40

Is the inspection result normal?

YES>>

Replace spindle unit RH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2437-11 Spindle Motor Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2437-11 Spindle motor RH (Spindle motor right hand) Diagnos...
    Dtc/circuit Diagnosis. B2437-13 Spindle Motor Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2437-13 Spindle motor RH (Spindle motor right hand) Diagnos...

    Other materials:

    U2648-87 Can Comm Circuit
    DTC Description CAN COMMUNICATIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is eq ...

    B2721-11 Center Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2721-11 CENTER SENSOR [RL] (Center sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH inner Threshold ...

    Repair Information. Preparation
    Repairing Material Foam Repair During factory body assembly, foam insulators are installed in certain body panels and locations around the Nissan Ariya vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.URETHANE FOAM APPLICATIONSUse commercially availabl ...