Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B242a-13 Closure Motor

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B242a-13 Closure Motor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B242A-13

Closure motor

(Closure motor) 		Diagnosis condition All times
Signal (terminal) Closure motor signal
Threshold Automatic back door control unit cannot detect the closure motor signal
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (closure motor circuit is open)

  • Automatic back door control unit

  • Back door lock assembly (closure motor)

FAIL-SAFE

Inhibit automatic back door system all function

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK BACK DOOR CLOSURE MOTOR INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+) (–) Condition

Voltage

(Approx.)
Automatic back door control unit
Connector Terminal
B56 33 Ground Back door closure motor Open operation Battery voltage
Other than above 5 V
34 Close operation Battery voltage
Other than above 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK BACK DOOR CLOSURE MOTOR CIRCUIT

  1. Disconnect automatic back door control unit connector and back door lock assembly connector.

  2. Check continuity between automatic back door control unit harness connector and back door lock assembly harness connector.

    Automatic back door control unit Back door lock assembly Continuity
    Connector Terminal Connector Terminal
    B56 33 D512 1 Yes
    34 2

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B56 33 Ground No
    34

Is the inspection result normal?

YES>>

Replace back door lock assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B242a-12 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-12 Closure motor (Closure motor) Diagnosis condition A...
    Dtc/circuit Diagnosis. B242a-19 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-19 Closure motor (Closure motor) Diagnosis condition A...

    Other materials:

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Parking brake
    Basic information WARNING Never drive the vehicle with the parking brake applied. The brake will overheat and fail to operate and will lead to an accident. Never release the parking brake from outside the vehicle. If the vehicle moves, it will be impossible to push the foot brake pedal and will l ...

    Tcm
    Reference Value CONSULT DATA MONITOR STANDARD VALUE In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine speed variation ...