Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2426-13 Spindle Sensor Lh

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2426-13 Spindle Sensor Lh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2426-13

Spindle sensor LH

(Spindle sensor left hand) 		Diagnosis condition When automatic back door open/close function operate
Signal (terminal) Encoder LH signal
Threshold Automatic back door control unit cannot detect the encoder LH signal
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Spindle unit LH

  • Automatic back door control unit

  • Harness or connector (encoder LH circuit is open)

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Operate automatic back door.

  3. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK ENCODER SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “Spindle sensor LH” in “Data monitor” mode of "AUTOMATIC BACK DOOR".

  3. Check that the function operates normally according to the following conditions.

    Monitor item Condition Status
    Spindle sensor LH Back door Open The numeral value increases
    Close The numeral value decreases

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 2.

CHECK ENCODER INPUT SIGNAL

Check signal between automatic back door control unit harness connector and ground using oscilloscope.

(+) (–) Condition

Signal

(Reference value)

(Approx.)
Automatic back door control unit
Connector Terminal
B55 29 Ground Back door Moving (auto)

When stopped 0 V or Battery voltage
30 Moving (auto)

When stopped 0 V or Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ENCODER CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit connector and spindle unit LH connector.

  3. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B55 29 B95 5 Yes
    30 3

  4. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 29 Ground No
    30

Is the inspection result normal?

YES>>

Replace spindle unit LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK ENCODER POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect spindle unit LH connector.

  3. Check voltage between spindle unit LH harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Spindle unit LH
    Connector Terminal
    B95 3 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

CHECK ENCODER CIRCUIT-1

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B55 31 B95 4 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 31 Ground No

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK ENCODER CIRCUIT-2

  1. Disconnect automatic back door control unit connector.

  2. Check continuity between automatic back door control unit harness connector and spindle unit LH harness connector.

    Automatic back door control unit Spindle unit LH Continuity
    Connector Terminal Connector Terminal
    B55 28 B95 2 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 28 Ground No

Is the inspection result normal?

YES>>

Replace spindle unit LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2426-12 Spindle Sensor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2426-12 Spindle sensor LH (Spindle sensor left hand) Diagno...
    Dtc/circuit Diagnosis. B2426-25 Spindle Sensor Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2426-25 Spindle sensor LH (Spindle sensor left hand) Diagno...

    Other materials:

    B24b4-02 A/c Control Comm
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B24B4-02 A/C CONTROL COMM (Air conditioning control communication) Diagnosis condition Ignition switch ON Signal (Terminal) LIN (A/C switch assembly) signal ...

    P1568 Icc Command Value
    DTC Description DTC DETECTION LOGICECM detects a difference between signals from ADAS control unit is out of specified range. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1568 00 ADAS COMMAND VALUE (ADAS function) Diagnosis condition — ...

    U2b52-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2B52 88 Ethernet comm err Diagnosis condition When engine is running Signal (terminal) Ethernet communication Threshold If ADAS control unit 2 is not ...