Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B1036-16 Ignition Voltage

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B1036-16 Ignition Voltage

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B1036-16

Ignition voltage

(Ignition voltage) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Ignition low voltage signal
Threshold Power supply malfunction (low voltage) of air bag diagnosis sensor unit
Diagnosis delay time 10 seconds or more.

POSSIBLE CAUSE

  • Malfunction of battery voltage (9 V or less)

  • Connection malfunction of harness or connector

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON and wait for 10 seconds or more.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK BATTERY VOLTAGE

Check battery voltage. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning parts.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace harness connectors.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B102a-55 Front Seat Belt Pre-Tensioner Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B102A-55 Front seat belt pre-tensioner RH (Front seat belt p...
    Dtc/circuit Diagnosis. B1036-17 Ignition Voltage
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1036-17 Ignition voltage (Ignition voltage) Diagnosis condi...

    Other materials:

    U1cab-02 Intake Door Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CAB-02 Intake door motor (Intake door motor) Diagnosis condition Ignition switch ON Signal (Terminal) LIN (door motor) signal Threshold A/C amp. i ...

    Electric Wastegate Control Actuator
    Component Inspection INSPECTION START Do you have CONSULT? Do you have CONSULT? YES>> GO TO 2. NO>> GO TO 3. CHECK ELECTRIC WASTEGATE CONTROL ACTUATOR With CONSULT Turn ignition switch ON and engine stopped. On the CONSULT screen, select “ENGINE”>>“ACTIVE ...

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...