Nissan Rogue Service Manual: C1735 ignition signal
DTC Logic
NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS sensor IDs
- Display tire pressure reported by the TPMS sensor
- Read TPMS DTCs
- Register TPMS sensor IDs
DTC DETECTION LOGIC
|
DTC |
Display Item |
Malfunction Detected Condition |
Possible Cause |
| C1735 | IGNITION SIGNAL LINE - BCM/ TPMS | BCM has detected a mismatch between IGN ON signals | BCM |
DTC CONFIRMATION PROCEDURE
1.PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
Perform Self Diagnostic Result.
Is DTC C1735 detected? YES >> Proceed to WT-36, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS sensor IDs
- Display tire pressure reported by the TPMS sensor
- Read TPMS DTCs
- Register TPMS sensor IDs
1.CHECK CAN IGNITION SIGNAL
With CONSULT
- Select “INTELLIGENT KEY” from “BCM” Data Monitor.
- Check IGN RLY1-F/B value.
|
Monitor item |
Displayed value |
|
IGN RLY1 F/B |
On with ignition in ON position |
Is the inspection result normal? YES >> GO TO 2.
NO >> Check CAN system. Refer to LAN-17, "Trouble Diagnosis Flow Chart".
2.CHECK BCM POWER SUPPLY AND GROUND
Check BCM power supply and ground. Refer to BCS-68, "Diagnosis Procedure" (with Intelligent Key System) or BCS-128, "Diagnosis Procedure" (without Intelligent Key System).
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3.DRIVE VEHICLE
Clear DTC and test drive vehicle to check for low tire pressure warning lamp.
Does the vehicle operate without any low tire pressure warning lamp? YES >> Inspection End.
NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key System) or BCS- 135, "Removal and Installation" (without Intelligent Key System).
C1734 BCM
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and dis ...
C1765, C1766, C1767, C1768 tire pressure sensor
DTC Description
DTC DETECTION LOGIC
DTC
Display Item
Malfunction Detected Condition
Possible Cause
C1765
WHEEL TOP DATA FL
(Wheel top data front left)
Malfunction i ...
Other materials:
Stall test
Work Procedure
INSPECTION
Check the engine oil level. Replenish if necessary. Refer to LU-7,
"Inspection".
Check for leak of the CVT fluid. Refer to TM-190, "Inspection".
Drive for about 10 minutes to warm up the vehicle so that the CVT
fluid temp ...
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
Precaution
Precautions for trouble diagnosis
CAUTION:
Never apply 7.0 V or more to the measurement terminal.
Use a tester with open terminal voltage of 7.0 V or less.
Turn the ignition switch OFF and disconnect the battery cable
from the negative terminal when
checking the harne ...
