Nissan Rogue Service Manual: C1716, C1717, C1718, C1719 transmitter (pressure data)

Nissan Rogue Service Manual / Suspension / Road Wheels & Tires / DTC/circuit diagnosis / C1716, C1717, C1718, C1719 transmitter (pressure data)

DTC Logic

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs
Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC	Display Item	Malfunction Detection Condition	Possible Cause
C1716	[PRESSDATA ERR] FL	Malfunction in the tire pressure data from the front LH wheel tire pressure sensor.	Excessive tire pressure ID registration incomplete Tire pressure sensor BCM
C1717	[PRESSDATA ERR] FR	Malfunction in the tire pressure data from the front RH wheel tire pressure sensor.
C1718	[PRESSDATA ERR] RR	Malfunction in the tire pressure data from the rear RH wheel tire pressure sensor.
C1719	[PRESSDATA ERR] RL	Malfunction in the tire pressure data from the rear LH wheel tire pressure sensor.

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

Check tire pressure for all wheels and adjust to the specified value. Refer to WT-65, "Tire Air Pressure".
Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
Perform Self Diagnostic Result.

Is DTC C1716, C1717, C1718, or C1719 detected? YES >> Proceed to WT-29, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs
Register TPMS sensor IDs

1.TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to WT-21, "Work Procedure".

Can the tire pressure sensor ID registration be completed? YES >> GO TO 2.

NO >> Replace applicable tire pressure sensor. Refer to WT-61, "Removal and Installation".

2.CHECK TIRE PRESSURE SIGNAL

With CONSULT

Adjust tire pressure for all wheels to the specified value. Refer to WT-65, "Tire Air Pressure".
Select “AIR PRESSURE MONITOR” from “BCM”.
Check that the air pressures match the specified value.

Monitor item	Displayed value
AIR PRESS FL	Approximately equal to specified value. Refer to WT-65, "Tire Air Pressure".
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL

Is the inspection result normal? YES >> Inspection End.

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key System) or BCS- 135, "Removal and Installation" (without Intelligent Key System).

C1708, C1709, C1710, C1711 transmitter (no data)

DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and dis ...

C1729 vehicle speed signal

DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and dis ...

Other materials:

B0010, B0011 passenger airbag module
DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order ASSIST AIRBAG MODULE CIRCUIT [OPEN] B0010 Front passenger air bag module circuit (AS1) is open. Refer to SRC-49, "Diagnosis Procedure". ASS ...

Wiring diagram
SRS AIR BAG SYSTEM Wiring Diagram ...

C1197 vacuum sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1197 VACUUM SENSOR When a malfunction is detected in vacuum sensor. Harness or connector Vacuum sensor (brake booster) Vacuum piping &nb ...