Nissan Rogue manuals

Nissan Rogue Service Manual: C1120, C1122, C1124, C1126 ABS in valve system

Nissan Rogue Service Manual / Brakes / Brake Control System / DTC/circuit diagnosis / C1120, C1122, C1124, C1126 ABS in valve system

DTC Logic

DTC DETECTION LOGIC

DTC Display Item Malfunction detected condition Possible causes
C1120 FR LH IN ABS SOL When a malfunction is detected in front LH ABS IN valve.
  • Harness or connector
  •  ABS actuator and electric unit (control unit)
  •  Fusible link
  •  Battery power supply system
C1122 FR RH IN ABS SOL When a malfunction is detected in front RH ABS IN valve.
C1124 RR LH IN ABS SOL When a malfunction is detected in rear LH ABS IN valve.
C1126 RR RH IN ABS SOL When a malfunction is detected in rear RH ABS IN valve.

DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

With CONSULT.

  1.  Turn ignition switch OFF to ON.
  2.  Perform self-diagnostic result.

Is DTC C1120, C1122, C1124 or C1126 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-87, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".

1.CONNECTOR INSPECTION

  1.  Turn ignition switch OFF.
  2.  Disconnect ABS actuator and electric unit (control unit) connectors.
  3.  Check connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace as necessary.

2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) BATTERY POWER SUPPLY

Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 25 and ground.

Check ABS actuator and electric unit (control unit) battery power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning components.

3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT

Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 13, 38 and ground.

Check ABS actuator and electric unit (control unit) ground circuit

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Repair or replace malfunctioning components.

C1115 ABS sensor [abnormal signal]
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1115 ABS SENSOR [ABNORMAL SIGNAL] When difference in wheel speed betw ...

C1121, C1123, C1125, C1127 ABS out valve system
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1121 FR LH OUT ABS SOL When a malfunction is detected in front LH ABS OU ...

Other materials:

C1765, C1766, C1767, C1768 tire pressure sensor
DTC Description DTC DETECTION LOGIC DTC Display Item Malfunction Detected Condition Possible Cause C1765 WHEEL TOP DATA FL (Wheel top data front left) Malfunction in the wheel top data from the front LH wheel speed sensor. Wheel speed sensor C1766 ...

Trouble diagnosis - specification value
Description The specification (SP) value indicates the tolerance of the value that is displayed in “SPEC” of “DATA MONITOR” mode of CONSULT during normal operation of the Engine Control System. When the value in “SPEC” of “DATA MONITOR” mode is within the SP value, the Engine ...

U0073 communication bus a OFF
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0073 COMM BUS A OFF (Control Module Communication Bus A Off) TCM communication blockage lasts for 2 seconds or more when turning ON the ignition sw ...

© 2014-2025 Copyright www.nirogue.com