Nissan Rogue (T33) 2021-Present Service Manual: B2faf-12 Ignition Relay-2

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Control System / Power Distribution System :: Dtc/circuit Diagnosis / B2faf-12 Ignition Relay-2

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detection condition
B2FAF-12

Ignition relay-2

(Ignition relay-2) 		Diagnosis condition When ignition switch is ON
Signal (terminal) Ignition relay-2 control signal [terminal #31 (with type A meter) or terminal #33 (with type B meter)]
Threshold 16 V or more
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors (ignition relay-2 control signal circuit is shorted to battery)

  • Ignition relay-2

  • BCM

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “BCM”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK IGNITION RELAY-2 CONTROL SIGNAL CIRCUIT (SHORT TO BATTERY)

  1. Ignition switch OFF.

  2. Disconnect BCM connector and ignition relay-2 connector.

  3. Check voltage between BCM harness connector and ground.

    With type A meter
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    M51 31 Ground 0 V
    With type B meter
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    M18 33 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the harness or connector.

CHECK IGNITION RELAY-2

Check ignition relay-2. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace ignition relay-2.

Component Inspection

CHECK IGNITION RELAY-2

  1. Ignition switch OFF.

  2. Disconnect ignition relay-2 connector.

  3. Check continuity between ignition relay-2 terminals.

Ignition relay-2 Condition Continuity
Terminal
12 V direct current supply between terminals and . Yes
No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace ignition relay-2.

    B2fae-14 Ignition Relay-1
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2FAE-14 Ignition relay-1 (Ignition relay-1) Diagnosis condi...
    B2faf-14 Ignition Relay-2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2FAF-14 Ignition relay-2 (Ignition relay-2) Diagnosis condi...

    Other materials:

    Dtc/circuit Diagnosis. B242a-98 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-98 Closure motor (Closure motor) Diagnosis condition When back door closure function operate Signal (terminal) — Threshold When thermal prot ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...

    U2b8c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2B8C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Lost ethernet communication with driving video recorder control module ...