Nissan Rogue (T33) 2021-Present Service Manual: B2731-88 Side Sensor [rr]

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / B2731-88 Side Sensor [rr]

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2731-88

SIDE SENSOR [RR]

(Side sensor [RR]) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Communication error
Diagnosis delay time 4 seconds or more

POSSIBLE CAUSE

  • Harness and connector between sonar control unit and rear sonar sensor RH side

  • Rear sonar sensor RH side

FAIL-SAFE

Stop the obstacle detection function

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check the DTC.

Is DTC “B2731–88” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK REAR SONAR SENSOR SIGNAL RH SIDE CIRCUIT (1)

  1. Turn ignition switch OFF.

  2. Disconnect sonar control unit connector and rear sonar sensor RH side connector.

  3. Turn ignition switch ON.

  4. Check voltage between sonar control unit harness connector and ground.

    Sonar control unit (-) Voltage (Approx. )
    Connector Terminal
    B49 50 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK REAR SONAR SENSOR SIGNAL RH SIDE CIRCUIT (2)

  1. Turn ignition switch OFF.

  2. Check continuity between rear sonar sensor RH side harness connector and ground.

Rear sonar sensor RH side Ground Continuity
Connector Terminal
B464 2 Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Connect sonar control unit connector and rear sonar sensor RH side connector.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B2731-88 detected again?

YES>>

Replace the rear sonar sensor RH side. Refer to Removal and Installation.

NO>>

INSPECTION END

    B2731-83 Side Sensor [rr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2731-83 SIDE SENSOR [RR] (Side sensor [RR]) Diagnosis condition...
    B2731-92 Side Sensor [rr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2731-92 SIDE SENSOR [RR] (Side sensor [RR]) Diagnosis condition...

    Other materials:

    Dtc/circuit Diagnosis. B0028-1a Side A/b Module Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0028-1A SIDE A/B MODULE RH (Right Side Airbag Deployment Control) Diagnosis condition When ignition switch is ON. Signal (terminal) Front side air bag modu ...

    Brake fluid
    For more information on brake fluid type and capacity, refer to “Capacities and recommended fluids/lubricants”. WARNING Always use new brake fluid from a sealed container. Contaminated, old, or poor-quality fluid may damage the brake system and reduce stopping performance. Clean the filler c ...

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...