Nissan Rogue (T33) 2021-Present Service Manual: B272a-88 Center Sensor [fl]

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / B272a-88 Center Sensor [fl]

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B272A-88

CENTER SENSOR [FL]

(Center sensor [FL]) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Communication error
Diagnosis delay time 4 seconds or more

POSSIBLE CAUSE

  • Harness and connector between sonar control unit and front sonar sensor LH inner

  • Front sonar sensor LH inner

FAIL-SAFE

Stop the obstacle detection function

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check the DTC.

Is DTC “B272A–88” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FRONT SONAR SENSOR SIGNAL LH INNER CIRCUIT (1)

  1. Turn ignition switch OFF.

  2. Disconnect sonar control unit connector and front sonar sensor LH inner connector.

  3. Turn ignition switch ON.

  4. Check voltage between sonar control unit harness connector and ground.

    Sonar control unit (-) Voltage (Approx. )
    Connector Terminal
    B20 2 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK FRONT SONAR SENSOR SIGNAL LH INNER CIRCUIT (2)

  1. Turn ignition switch OFF.

  2. Check continuity between front sonar sensor LH inner harness connector and ground.

Front sonar sensor LH inner Ground Continuity
Connector Terminal
E305 2 Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Connect sonar control unit connector and front sonar sensor LH inner connector.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B272A-88 detected again?

YES>>

Replace the front sonar sensor LH inner. Refer to Removal and Installation.

NO>>

INSPECTION END

    B272a-83 Center Sensor [fl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B272A-83 CENTER SENSOR [FL] (Center sensor [FL]) Diagnosis condi...
    B272a-92 Center Sensor [fl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B272A-92 CENTER SENSOR [FL] (Center sensor [FL]) Diagnosis condi...

    Other materials:

    Dtc/circuit Diagnosis. C18de-82 Brake Power Supply Back up Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition C18DE 82 Backup power supply unit communication Diagnosis condition When Ignition switch is ON. Signal (terminal) Brake power supply backup unit signal Threshold When a malfunct ...

    Information Display (combination Meter)
    Door Open Warning DESIGN/PURPOSEInformation display warns the driver that each door is open or is not fully closed. Symbol Message – SYNCHRONIZATION WITH MASTER WARNING LAMPSynchronization is applied.Refer to Master Warning Lamp.SYSTEM DIAGRAMSIGNAL PATH BCM transmits door switch ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...