Nissan Rogue (T33) 2021-Present Service Manual: B2720-88 Corner Sensor [rl]

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Sonar System / Dtc/circuit Diagnosis :: Sonar (sonar Control Unit) / B2720-88 Corner Sensor [rl]

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition
B2720-88

CORNER SENSOR [RL]

(Corner sensor [rear left]) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Communication error
Diagnosis delay time 4 seconds or more

POSSIBLE CAUSE

  • Harness and connector between sonar control unit and rear sonar sensor LH outer

  • Rear sonar sensor LH outer

FAIL-SAFE

Stop the obstacle detection function

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 30 seconds.

  3. Turn ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “SONAR” using CONSULT.

  5. Check the DTC.

Is DTC “B2720–88” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK REAR SONAR SENSOR SIGNAL LH OUTER CIRCUIT (1)

  1. Turn ignition switch OFF.

  2. Disconnect sonar control unit connector and rear sonar sensor LH outer connector.

  3. Turn ignition switch ON.

  4. Check voltage between sonar control unit harness connector and ground.

    Sonar control unit (-) Voltage (Approx. )
    Connector Terminal
    B20 22 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK REAR SONAR SENSOR SIGNAL LH OUTER CIRCUIT (2)

  1. Turn ignition switch OFF.

  2. Check continuity between rear sonar sensor LH outer harness connector and ground.

Rear sonar sensor LH outer Ground Continuity
Connector Terminal
B457 2 Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

  1. Connect sonar control unit connector and rear sonar sensor LH outer connector.

  2. Turn ignition switch ON.

  3. Erase DTC.

  4. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC B2720-88 detected again?

YES>>

Replace the rear sonar sensor LH outer. Refer to Removal and Installation.

NO>>

INSPECTION END

    B2720-83 Corner Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2720-83 CORNER SENSOR [RL] (Corner sensor [rear left]) Diagnosi...
    B2720-92 Corner Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2720-92 CORNER SENSOR [RL] (Corner sensor [rear left]) Diagnosi...

    Other materials:

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    B2723-88 Corner Sensor [rr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2723-88 CORNER SENSOR [RR] (Corner sensor [RR]) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Communication error D ...

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...