Nissan Rogue (T33) 2021-Present Service Manual: Awd :: Preparation. Preparation

Preparation

Special Service Tool

Tool number

(TechMate No.)

Tool name
Description

KV40104000

( – )

Hub lock nut wrench

a: 85 mm (3.35 in)

b: 65 mm (2.56 in)

Removing and Installing wheel hub lock nut.

KV40107300

( – )

Boot band crimping tool

Installing boot band

KV40107310

( – )

Boot band crimping tool

Installing boot band

KV38107900

( – )

Protector

a: 32 mm (1.26 in) dia.

b: 25 mm (0.98 in)

Installing drive shaft

(NI-52982)

Lock nut chisel (Cape chisel)

Removing wheel hub lock nut

Commercial Service Tool

Tool name Description
Drive shaft joint puller

Removing drive shaft
Ball joint remover

  • Removing ball joint for suspension arm

  • Removing hub bolt

Power tool

Loosening nuts, screws and bolts
Lock nut crimp punch (Cold chisel)

Installing wheel hub lock nut

a: 5 mm (0.20 in)

b: 7 mm (0.28 in)

Lubricant or/and Sealant

Name Description
NISSAN Genuine grease or equivalent
  • Joint sub-assembly inside

  • Housing inside

Apply paste [service parts (440037S000)]
  • Joint sub-assembly

Always Replace with New Parts

Never Reuse These Parts Part Code For additional information:
Nut-Lock, Wheel Bearing 40262 Exploded View
Bolt 40030A Exploded View
Bolt - Hub 40222 Exploded View
Nut 40080B Exploded View
Circlip - Side Gear 38225W Exploded View
Shield - Dust 39752+B Exploded View
Ring - Snap Exploded View
Ring - Stopper Exploded View
Band Boot - Sld Hsq Exploded View
Boot - Fixed JT 39155KA Exploded View
Band - Damp Exploded View
Band - Boot, Hsq Exploded View
Band - Boot, SFT Exploded View
Boot - Fixed JT 39155KA Exploded View
Circlip - Drive Sft Exploded View
Circlip - Drive Sft 39234 Exploded View
Boot - Fixed JT 39155K Exploded View
Boot - Slide JT, Rub 39156K Exploded View
Ring - Snap 39734 Exploded View
Ring - Stopper 39735+A Exploded View
Ring - Snap Exploded View
Shield - Dust 39752+A Exploded View
Shield - Dust 39752+B Exploded View
Shield - Dust 39752 Exploded View
Shield - Dust 39752 Exploded View
    Awd. Precaution. Precautions
    Precautions Precautions for Removing Battery Terminal With the adoption of Auto ACC function, ACC power is automatically supplied by operating the Intelligent Key or remote keyl...
    Awd. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use chart below to find the cause of the symptom. If necessary, repair or replace these parts. Pos...

    Other materials:

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Chassis control
    Basic information The chassis control system in the Nissan Rogue uses an electric control module that manages the following functions: Intelligent Trace Control Active Ride Control (if so equipped) Intelligent Trace Control This feature analyzes the driver’s steering, acceleration and braking ...

    C1f59-04 Eps Circuit
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F59 04 EPS control unit (Electric power steering control unit) Diagnosis condition When engine is running Signal (termi ...