Nissan Rogue Service Manual: Precaution
Precaution for supplemental restraint system (srs) "air bag" and "seat
belt
pre-tensioner"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
driver and front passenger for certain
types of collision. Information necessary to service the system safely is
included in the SR and SB section of
this Service Manual.
WARNING:
- To avoid rendering the SRS inoperative, which could increase
the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all
maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
- Improper maintenance, including incorrect removal and
installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of
Spiral Cable and Air Bag
Module, see the SR section.
- Do not use electrical test equipment on any circuit related to
the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or
orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
- When working near the Airbag Diagnosis Sensor Unit or other
Airbag System sensors with the Ignition
ON or engine running, DO NOT use air or electric power tools or strike near
the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air
bag(s), possibly causing
serious injury.
- When using air or electric power tools or hammers, always
switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.

Precaution for battery service
Before disconnecting the battery, lower both the driver and passenger
windows. This will prevent any interference
between the window edge and the vehicle when the door is opened/closed. During
normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle
interference. The automatic
window function will not work with the battery disconnected.
Service notice or precautions for transfer
- After overhaul refill the transfer with new transfer oil.
- Check the oil level or replace the oil only with the vehicle
parked on level surface.
- During removal or installation, keep inside of transfer clear of
dust or dirt.
- Replace all tires at the same time. Always use tires of the proper
size and the same brand and pattern. Fitting
improper size and unusual wear tires applies excessive force to vehicle
mechanism and can cause longitudinal
vibration.
- Disassembly should be done in a clean work area.
- Before proceeding with disassembly, thoroughly clean the transfer. It is
important to prevent the internal
parts from becoming contaminated by dirt or other foreign matter.
- Check for the correct installation status prior to removal or
disassembly. If matching marks are required, be
certain they do not interfere with the function of the parts when applied.
- All parts should be carefully cleaned with a general purpose,
non-flammable solvent before inspection or
reassembly.
- Check appearance of the disassembled parts for damage,
deformation, and unusual wear. Replace them
with a new one if necessary.
- Gaskets, seals, O-rings and lock nuts should be replaced any time
when the transfer is disassembled.
- In principle, tighten bolts or nuts gradually in several steps
working diagonally from inside to outside. If tightening
sequence is specified, use it.
- Observe the specified torque when assembling.
- Clean and flush the parts sufficiently and blow-dry them.
- Be careful not to damage sliding surfaces and mating surfaces.
- Use lint-free cloth or towels for wiping parts clean. Common shop
rags can leave fibers that could interfere
with the operation of the transfer.
Special service tool
The actual shapes of techmate tools may differ from those of special service
tools illustrated here.
Tool number
(techmate no.)
Tool name
Description
...
Other materials:
P1217 engine over temperature
DTC Description
DTC DETECTION LOGIC
If the cooling fan or another component in the cooling system malfunctions,
engine coolant temperature will
rise.
When the engine coolant temperature reaches an abnormally high temperature
condition, a malfunction is
indicated.
DTC No.
CONSUL ...
Camshaft valve clearance
Camshaft valve clearance
Perform this inspection as follows after removal, installation, or
replacement of the camshaft or any valve
parts, or if there are any unusual engine conditions due to changes in valve
clearance over time (starting,
idling, and/or noise).
Remove the ...
Washer tank
Exploded View
Cap
Washer tank
Washer tank inlet
Clip
Removal and Installation
REMOVAL
Drain washer fluid.
Using a suitable tool release washer tank inlet clip and remove
washer tank inlet.
Remove engine side cover. Refer EXT-28, "FEND ...
© 2014-2025 Copyright www.nirogue.com