Nissan Rogue Service Manual: DTC/circuit diagnosis
B2600-46 CONFIG ERROR
DTC Description
DTC DETECTION LOGIC
|
DTC |
Trouble diagnosis (Trouble diagnosis contents) |
Detecting condition |
| B2600-46 | CONFIG ERROR (Configuration error) | When errors are detected in the configuration data stored in the BCM (CAN gateway function). |
POSSIBLE CAUSE
BCM
FAIL-SAFE
Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
- Turn ignition switch ON and wait at least 2 seconds or more.
- Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
- Check DTC.
Is DTC B2600-46 detected? YES >> Proceed to LAN-78, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
1.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
- Turn ignition switch ON.
- Erase DTC.
- Perform DTC confirmation procedure again. Refer to LAN-78, "DTC Description".
- Check DTC.
Is DTC B2600-46 detected again? YES >> Replace BCM. Refer to the following.
- WIth Intelligent Key system: BCS-75, "Removal and Installation".
- WIthout Intelligent Key system: BCS-135, "Removal and Installation".
NO >> INSPECTION END
B2600-55 CONFIG ERROR
DTC Description
DTC DETECTION LOGIC
|
DTC |
Trouble diagnosis (Trouble diagnosis contents) |
Detecting condition |
| B2600-55 | CONFIG ERROR (Configuration error) | When no data are stored in the BCM (CAN gateway function). |
POSSIBLE CAUSE
- Configuration is incomplete
- BCM
FAIL-SAFE
Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
- Turn ignition switch ON and wait at least 2 seconds or more.
- Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
- Check DTC.
Is DTC B2600-55 detected? YES >> Proceed to LAN-79, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
1.PERFORM CONFIGURATION OF CAN GATEWAY
Perform CAN gateway configuration. Refer to LAN-77, "Work Procedure".
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE AGAIN
- Turn ignition switch ON.
- Perform DTC confirmation procedure again. Refer to LAN-79, "DTC Description".
- Check DTC.
Is DTC B2600-55 detected again? YES >> Replace BCM. Refer to the following.
- WIth Intelligent Key system: BCS-75, "Removal and Installation".
- WIthout Intelligent Key system: BCS-135, "Removal and Installation".
NO >> INSPECTION END
Basic inspection
CONFIGURATION (CAN GATEWAY)
Work Procedure
1.WRITING MODE SELECTION
CONSULT Configuration
Select “Re/programming, Configuration” of CAN gateway.
When writing saved data>>GO TO 2.
W ...
CAN system (type 1)
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT
Diagnosis Procedure
1.CHECK CONNECTOR
Turn the ignition switch OFF.
Disconnect the battery cable from the negative t ...
Other materials:
Readiness for inspection/maintenance (I/M) test
WARNINGA vehicle equipped with All -Wheel Drive
(AWD) should never be tested using a two
wheel dynamometer (such as the dynamometers
used by some states for emissions
testing), or similar equipment. Make
sure you inform the test facility personnel
that your vehicle is equipp ...
Brake booster
Inspection
Operation
Depress the brake pedal several times at five second intervals with
the engine stopped. Start the engine with the brake pedal fully
depressed. Check that the clearance between brake pedal and dash
lower panel decreases.
NOTE:
A slight impact with a small click may be fe ...
System description
COMPONENT PARTS
Component Parts Location
Center of back door
No.
Component
Function
1
Rod antenna
Refer to AV-14, "Rod Antenna, Antenna Amp., Satellite
Antenna and Antenna Feeder".
2
Antenna base (antenna amp. and sa ...
