Description
DTC B0096 FRONT SATELLITE SENSOR RH
The front side air bag satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the front side air bag satellite sensor RH for internal failures and its circuits for communication errors.
PART LOCATION
Refer to SRC-6, "Component Parts Location".
DTC Logic
DTC DETECTION LOGIC
With CONSULT
CONSULT name |
DTC |
DTC detecting condition |
Repair order |
B-PILLAR SATELLITE SENSOR RH [SENSOR FAIL] | B0096 | Front side air bag satellite sensor RH has malfunctioned. | Refer to SRC-78, "Diagnosis Procedure". |
B-PILLAR SATELLITE SENSOR RH [COMM FAIL] | Front side air bag satellite sensor RH communication error. | ||
B-PILLAR SATELLITE SENSOR RH [DISCONNECT] | Front side air bag satellite sensor RH is disconnected. | ||
B-PILLAR SATELLITE SENSOR RH [UNMATCH] | Front side air bag satellite sensor RH is out of specification. | ||
B-PILLAR SATELLITE SENSOR RH [GND-SHORT] | Front side air bag satellite sensor RH circuit is shorted to ground. |
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.CHECK SELF-DIAG RESULT
Is the DTC detected? YES (Current DTC)>>Refer to SRC-78, "Diagnosis Procedure".
YES (Past DTC)>>GO TO 2.
NO >> Inspection End.
2.ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased? YES >> Inspection End.
NO >> Refer to SRC-78, "Diagnosis Procedure".
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.CHECK SELF-DIAG RESULT
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-78, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 2.
NO >> Perform one of the following repairs:
2.CONFIRM DTC
Is DTC still current? YES >> GO TO 3.
NO >> Refer to GI-41, "Intermittent Incident".
3.WIRING HARNESS
Check the wiring harness for visible damage.
NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the harness.
4.CONFIRM DTC
Is DTC still current? YES >> GO TO 5.
NO >> Refer to GI-41, "Intermittent Incident".
5.FRONT SIDE AIR BAG SATELLITE SENSOR RH
Is DTC still current? YES >> GO TO 6.
NO >> Clear DTC. Inspection End.
6.AIR BAG DIAGNOSIS SENSOR UNIT
Is DTC still current? YES >> GO TO 7.
NO >> Clear DTC. Inspection End.
7.RELATED HARNESS
Replace the related harness.
>> END
VIN registration
Description
VIN Registration is an operation to registering VIN in ECM. It must be
performed each time ECM is replaced.
NOTE:
Accurate VIN which is registered in ECM may be required for Inspection &
Maintenance (I/M).
Work Procedure
1.CHECK VIN
Check the VIN of the vehicle and note it. ...
The parking brake release warning continues sounding, or
does not sound
Description
The parking brake warning buzzer sounds continuously during vehicle
travel though the parking brake is
released.
The parking brake warning buzzer does not sound at all even though
driving the vehicle with the parking
brake applied.
Diagnosis Procedure
1. CHECK P ...
Removal and installation
CHASSIS CONTROL MODULE
Exploded View
Steering member
Chassis control module
Front
Removal and Installation
CAUTION:
When replacing chassis control module, configuration of chassis control module
is required. Refer to
DAS-205, "Work Procedure".
REMOVAL
NOTE:
...